1-20 of 21 Search Results for

301

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.mech.c0006900
EISBN: 978-1-62708-225-9
... Abstract Several type 301 half-hard stainless steel clamps used to hold cylindrical galvanized steel covers to galvanized cast iron bases failed in flooded manholes after one to six months of service. Before service, they were treated with antiseize compound containing MoS2. Based on the...
Series: ASM Failure Analysis Case Histories
Volume: 2
Publisher: ASM International
Published: 01 December 1993
DOI: 10.31399/asm.fach.v02.c9001360
EISBN: 978-1-62708-215-0
... Abstract A blade from the engine cooling fan of a pickup truck fractured unexpectedly. The blade was made from type 301 stainless steel in the extra full hard tempered condition with a hardness of 47 HRC. Failure analysis indicated that the blade fractured in three modes: crack initiation...
Series: ASM Failure Analysis Case Histories
Volume: 1
Publisher: ASM International
Published: 01 December 1992
DOI: 10.31399/asm.fach.v01.c9001086
EISBN: 978-1-62708-214-3
... Abstract Two Z-shape impeller vanes failed. The vane material was 14-hard type 301 stainless steel. The vanes were of two-piece construction, with a longitudinal weld. Analyses indicated that the vanes had not been solution annealed after welding, leaving the heat-affected zone above the welds...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.aero.c9001905
EISBN: 978-1-62708-217-4
... premature failure. The chemical composition of the components was compatible with the nominal composition of Type 302 stainless steel, which conformed to the governing requirement (Type 301 or 302). However, dimensional inspection revealed that the band was thinner than required and the hardness was lower...
Series: ASM Failure Analysis Case Histories
Volume: 1
Publisher: ASM International
Published: 01 December 1992
DOI: 10.31399/asm.fach.v01.c9001075
EISBN: 978-1-62708-214-3
... sensitive. Additionally, data in Ref 5 show that with a stress-concentration factor of 3, “extra hard” type 301 and annealed type 304L stainless steel have about the same fatigue strength. Fig. 8 Fatigue curves for cold-drawn type 304 austenitic stainless steel, showing that the cold-worked...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001845
EISBN: 978-1-62708-241-9
... in thin sheet twin-roll cast aluminum alloys . Mater. Charact . 37 , 301 – 310 ( 1996 ) 10.1016/S1044-5803(97)80019-8 4. Chu Q. , Zhang M. , Li J. , Failure analysis of impeller made of FV520B martensitic precipitated hardening stainless steel . Eng. Fail. Anal . 34...
Series: ASM Failure Analysis Case Histories
Volume: 1
Publisher: ASM International
Published: 01 December 1992
DOI: 10.31399/asm.fach.v01.c9001020
EISBN: 978-1-62708-214-3
... ( Fig. 10 ), however, was not as advanced as the cracking in the left lug; the cracks were shallower and not as numerous (note the differences in magnification in Fig. 8 , 9 , 10 ). Fig. 10 Cracking associated with fracture of right lower attachment lug. Unetched. 301×. Results of...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.conag.c9001637
EISBN: 978-1-62708-221-1
... 313 31 X 4 303 32 X 16 279 33 X 4 … 34 X 5 297 35 X 4 … 36 X 5 290 37 X 5 … 38 X 5 295 39 X 6 283 40 X 6 … 41 X 5 295 42 X 4 … 43 X 4 301 44 AVH … 313 (a) (a) HV 20 Hardness measurements were made on a...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.power.c9001561
EISBN: 978-1-62708-229-7
... Sec −1 can be obtained which would be in the sensitizing range of the material. The effects of varying chloride concentrations on stainless steel ( 6 , 12 ) below 135°C have produced intergranular cracking in both 304 and 304L stainless steel. Also work by Bednar ( 13 ) suggests that alloys of 301...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.power.c9001594
EISBN: 978-1-62708-229-7
... Research Institute , San Antonio, TX , Sep 1993 . 3. CPSES Welding Manual , Welding Procedure Specifications CP-301 for stainless steel and CP-201 for carbon steel, Comanche Peak Steam Electric Station. 4. CPSES Welding Manual , Procedure WLD-106, Section 6.9.1, Comanche Peak Steam Electric...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006829
EISBN: 978-1-62708-295-2
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003565
EISBN: 978-1-62708-180-1
... 469 – 476 5. Rice S.L. , The Role of Microstructure in the Impact Wear of Two Aluminium Alloys , Wear , Vol 54 ( No. 2 ), 1978 , p 291 – 301 6. Rice S.L. and Wayne S.F. , Wear of Two Titanium Alloys Under Repetitive Compound Impact , Wear , Vol 61 , 1980 , p...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003571
EISBN: 978-1-62708-180-1
... 301 – 312 23. Moore D.F. , Friction and Wear in Rubbers and Tyres , Wear , Vol 61 , 1980 , p 273 – 282 24. Liu T. and Rhee S.K. , High Temperature Wear of Semi-Metallic Disk Brake Pads , Wear of Materials 1977 , American Society of Mechanical Engineers , 1977...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003555
EISBN: 978-1-62708-180-1
... (a) 1200 (a) 2 9Cr-Mo 675 1250 3 Stainless steels 201, 202 845 1555 4 301 900 1650 4 302, 304 925 1695 4 309 1095 2000 4 310 1150 2100 4 316, 317, 321, 347 925 1695 4 330 1150 2100 4 405, 410 705 1300 4 416 675...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001814
EISBN: 978-1-62708-180-1
... , 1971 , p 38 – 42 • Doyle F.D. , Effect of Different Heat Treatments on the Wear of High Speed Steel Cutting Tools , Wear , Vol 27 , 1974 , p 295 – 301 • Doyle F.D. , Influence of High Speed Steel Microstructure on Tool Failure , in International Conference on Production...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006793
EISBN: 978-1-62708-295-2
... Wear of Two Aluminium Alloys , Wear , Vol 54 ( No. 2 ), 1987 , p 291 – 301 10.1016/0043-1648(79)90121-2 9. Rice S.L. and Wayne S.F. , Wear of Two Titanium Alloys under Repetitive Compound Impact , Wear , Vol 61 , 1980 , p 69 – 76 10.1016/0043-1648(80)90112-X 10...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006787
EISBN: 978-1-62708-295-2
... 301 900 1650 6 302, 304 925 1695 6 309 1095 2005 6 310 1150 2100 6 316, 317, 321, 347 925 1695 6 330 1150 2100 6 405, 410 705 1300 6 416 675 1245 6 420 620 1150 6 430 815 1500 6 440 760 1400 6 442 980 1795 6...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003553
EISBN: 978-1-62708-180-1
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003538
EISBN: 978-1-62708-180-1
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006775
EISBN: 978-1-62708-295-2