1-8 of 8 Search Results for

1117

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.mech.c0048661
EISBN: 978-1-62708-225-9
.... The taper pin was made of 1141 steel, the shaft 1117 steel, and the drive wheel 52100 steel. It was found that failure of the clutch-drive support assembly occurred as a result of fatigue fracture of the taper pin. A loose fit between the drive wheel and the shaft and between the drive wheel and the pin...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.process.c0092148
EISBN: 978-1-62708-235-8
... carburized. The cylinder in which the spool fitted was made of 1117 steel, also gas carburized. Investigation (visual inspection, low magnification images, 400x images, metallographic exam, and hardness testing) supported the conclusion that momentary sliding contact between the spool and the cylinder wall...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001759
EISBN: 978-1-62708-241-9
... assembly. drive shaft bearing cup brittle fracture heat treatment carbon steel shallow case endurance and load testing fracture toughness SAE-AISI 1117 (11xx resulfurized steel) UNS G11170 Introduction The automobile is a typical industrial product that involves a variety of materials...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.process.c9001241
EISBN: 978-1-62708-235-8
... ) 1239 , 1249 . 6. Class I. , Stahl und Eisen 80 ( 1960 ) 1117 / 1135 . 7. Nelson G. A. , Stahl und Eisen 80 ( 1960 ) 1134 . 8. Naumann F. K. , Stahl und Eisen 57 ( 1937 ) 889 / 899 . Selected References Selected References • Pond R.B. Jr...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003573
EISBN: 978-1-62708-180-1
... heat treatment, producing a low-strength structure of ferrite and tempered martensite. Fig. 11 Cross sections through the carburized 1117 steel cylinders from two spool-type hydraulic valves. The cylinder of the valve that operated satisfactorily (a) had little retained austenite in the case...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006797
EISBN: 978-1-62708-295-2
... type of ammunition were fired in the test. (a) Inside diameter. (b) Outside diameter Fig. 11 Cross sections through the carburized 1117 steel cylinders from two spool-type hydraulic valves. The cylinder of the valve that operated satisfactorily (a) had little retained austenite in the case...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003514
EISBN: 978-1-62708-180-1
... distribution of tensile properties among different heats of grade 1117 cold-drawn steel bars. Tested were round bars, 25 mm (1 in.) in diameter, 25 heats from 2 mills. The coefficient of variation is defined as: C X = s X X ¯ The coefficient of variation (COV) is widely used...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0001812
EISBN: 978-1-62708-180-1