1-7 of 7 Search Results for

100-70-03

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.chem.c0047220
EISBN: 978-1-62708-220-4
... tensile strength of 290 MPa (42 ksi) at 207 HRB. The smaller gear was sand cast from ASTM A536, grade 100-70-03, ductile iron with a tensile strength of 696 MPa (101 ksi) at 241 HRB. Analysis (metallographic examination) supported the conclusion that excessive beam loading and a lack of ductility in the...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.power.c9001561
EISBN: 978-1-62708-229-7
... and subjecting 304 and 304L specimens to cyclic loading tests that carbon contents of less than .03% produced no failures after 2000–3000 cycles while carbon contents of .05% or higher produced failures after less than 100 cycles. Failures observed were intergranular in nature. The effects of...
Series: ASM Failure Analysis Case Histories
Volume: 3
Publisher: ASM International
Published: 01 December 2019
DOI: 10.31399/asm.fach.v03.c9001816
EISBN: 978-1-62708-241-9
... material is considered to have superplastic behavior when it shows extremely high and uniform elongations (from 100 to 1000%) under tension stress: a lack of localized necking or a series of diffuse necks along the test zone resulting from a combination of the creep tension stress and the strain rate...
Series: ASM Failure Analysis Case Histories
Publisher: ASM International
Published: 01 June 2019
DOI: 10.31399/asm.fach.marine.c9001617
EISBN: 978-1-62708-227-3
... hydraulic fluid, although this could sometimes become contaminated with seawater if external couplings cracked. Temperatures experienced by the couplings ranged from 10 to 100 °C (50 to 212 °F), depending on their location. Table 2 Mechanical Properties of NAB in Accordance with DGS 1043 Issue 03 3...
Series: ASM Handbook
Volume: 11
Publisher: ASM International
Published: 15 January 2021
DOI: 10.31399/asm.hb.v11.a0006778
EISBN: 978-1-62708-295-2
... predominant in the matrix, it imparted substantial ductile behavior. Fig. 8 Crack in a high-strength ductile iron (grade 100-70-03) impeller showing deformation in the ferrite, resulting in blunting of this secondary crack. 2% nital etch. Original magnification: 492× In many cases, a combination...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003543
EISBN: 978-1-62708-180-1
..., substantial ductile character was imparted. Fig. 8 Crack in a high-strength ductile iron (grade 100-70-03) impeller showing deformation in the ferrite resulting in blunting of this secondary crack. 2% nital etch. 492× In many cases, a combination of fracture mechanisms suggests a minority phase...
Series: ASM Handbook Archive
Volume: 11
Publisher: ASM International
Published: 01 January 2002
DOI: 10.31399/asm.hb.v11.a0003508
EISBN: 978-1-62708-180-1
... Common name Sketch Metallic Projections A 100: Metallic projections in the form of fins or flash A 110: Metallic projections in the form of fins (or flash) without change in principal casting dimensions A 111 Thin fins (or flash) at the parting line or at core prints Joint...