Each of the ten studs on one wheel of a semitrailer used to haul coal broke in half while the trailer was in operation. Both halves of each of three studs were sent to the laboratory to determine the cause of failure. Visual examination of the fracture surfaces of the studs disclosed beach marks, indicative of fatigue cracking, starting at opposite sides of each stud, with final fracture occurring across the stud. Each failure occurred in the first thread of the stud. It was concluded that the wheel studs fractured by reversed-bending fatigue. To minimize the possibility of a recurrence, the wheel nuts were tightened with an air impact wrench to a torque of 610 to 678 J (450 to 500 ft · lb) dry. All wheel studs were checked at normal maintenance periods to ensure uniform and proper loading, and no further failures occurred.

An automotive front-wheel outer angular-contact ball bearing generated considerable noise shortly after delivery of the vehicle. The inner and outer rings were made of seamless cold-drawn 52100 steel tubing, the balls were forged from 52100 steel, and the retainer was stamped from 1008 steel strip. The inner ring, outer ring, and balls were austenitized at 845 deg C (about 1550 deg F), oil quenched, and tempered to a hardness of 60 to 64 HRC. Investigation (visual inspection) supported the conclusion that failure was caused by fretting due to vibration of the stationary vehicle position without bearing rotation. Recommendations included improving methods of securing the vehicle during transportation to eliminate vibrations.

Six galvanized high-tensile steel bolts were used to hold the wheels of a four-wheel drive vehicle. The right hand rear wheel of this vehicle detached causing the vehicle to roll and resulting in considerable damage to the body. The wheel was detached by shearing of four of the bolts and stripping the nuts from the other two bolts, which remained unbroken. SEM fractography of the fracture surfaces of the four broken bolts indicated that the failure was due to reversed bending fatigue. Optical microscopy indicated that the bolts were heat treated to a tempered martensite structure and that the nuts were manufactured from low carbon steel. The paper discusses the influence of the microstructure on the failure process the events surrounding the nature of incident and the analysis of in-service failure of the failed components utilizing conventional metallurgical techniques.

A suspension bushing separated from the disk on the rear wheel suspension of a racing vehicle while under operation on an express highway, causing the wheel to detach from the car. Visual inspection showed fresh turning grooves at four built-up fillet welds on the torus of the outside of the disk. The welding heat and rapid cooling caused the base material of the disk – already with a martensitic structure – to harden throughout the torus, both of which caused cracking in the inner and outer fillets at the transition from bushing to disk. Visual inspection of the other rear wheel showed similar stress cracks in the hardened base material of the transition region as well as the same four welds. Rough finishing and the sharp-edged formation of the cross section transition may have also contributed to the failure. The results of the investigation suggested that machine shops neither execute nor permit repair-welds on highly stressed machine parts and especially vehicle components.

A double-flange trailer wheel, in service on a coke-oven pusher car for about five years, broke. Specifications called for rolled steel track wheels conforming to ASTM A 186 (since reclassified as A 504). Chemical analysis showed the metal in the wheel to be medium-carbon steel within the ranges given in ASTM A 186. Visual examination of the broken wheel revealed that cracks ran parallel with the base of the lower row of numbers stamped with heavy indentation on the web section. Microscopic examination showed the metal in the web, rim, and tread to be in the normalized condition. Evidence found supports the conclusions that fatigue failure of the wheel was the result of heavy stamp marks that acted as stress raisers in the weaker web section. Because this was a double-flange wheel, considerable side thrust was applied to the wheel, causing stress concentration at the web. Recommendations included following the ASTM specification A 504 regarding location of stamped identification numbers (marks identifying the wheels must be stamped on the back face of the rim not less than 3.2 mm from the inner edge of the rim).

Several case-hardened and zinc-plated carbon-manganese steel wheel studs fractured in a brittle manner after very limited service life. The fracture surfaces of both front and rear studs showed no sign of fatigue beach marks or deformation in the form of shear lips that would indicate either a fatigue mechanism or ductile overload failure. SEM analysis revealed that the mode of fracture was intergranular decohesion, which indicates an environmental influence in the fracture mechanism. The primary fracture initiated at a thread root and propagated by environmentally-assisted slow crack growth until final fracture. The natural stress concentration at the thread root, when tightened to the required clamp load concomitant with the presence of cracks in the carburized case, was sufficient to exceed the critical stress intensity for hydrogen-assisted stress cracking (HASC). The zinc plating exacerbated the situation by providing a strong local corrosion cell in the form of a sacrificial anode region adjacent to the cracked thread. The enhanced generation of hydrogen in a corrosive environment subsequently lead to HASC of the wheel studs.

A sand-cast LM6M aluminum alloy sprocket drive wheel in an all-terrain vehicle failed. Extensive cracking had occurred around each of the six bolt holes in the wheel. Evidence of considerable deformation in this area was also noted. Examination indicated that the part failed because of gross overload. Use of an alloy with a much higher yield strength and improvement in design were recommended.

Failure of carbon-manganese steel wheel studs caused by improper tightening of the inner wheel nuts resulted in separation of a dual wheel assembly on a heavy truck. The benchmark pattern observed on the fracture surfaces of the studs evidenced fatigue cracks emanating from multiple origins around the circumference. There was no indication that any microstructural characteristics of the material contributed to the failure. Inclusions that were present were small and relatively few in number. Failure to check the torque of the inner wheel nuts as per the manufacturer's recommendation caused the inner wheel nuts to loosen during break-in and lose the required clamping force. The development and promotion of educational programs on proper wheel tightening procedures was recommended.

The rear outside wheel of an over-the-road 18-wheel tractor-trailer failed at its bolt holes, permitting the tire and wheel to separate from the hub. Failure analysis was conducted using photographic examination of actual fracture surfaces and SEM examination of fracture replicas. The examinations indicated that fatigue cracks had originated at the rim backside and propagated to the rim midsection. Catastrophic failure occurred at a final overland. Fatigue fracture of the wheel rim was attributed to cyclic loading created by improper wheel mounting of a spare tire.