Search Results for vacuum degassing

Driven by the need to reduce CO 2 emissions through increased steam temperature and pressure in new power plants, research in Europe led to the development of enhanced high-chromium steels with improved creep resistance and service temperature stability. After years of development, Rotor E, a steel composition created during the COST programs (501, 522, and 536), has become a commercially available product. While traditionally forged and remelted using electroslag remelting (ESR), this paper demonstrates the successful production of large rotor components using a conventional process without ESR, achieved through tailored process control. This paper details Società delle Fucine's (SdF) current production of Rotor E using a conventional route based on ladle furnace and vacuum degassing, as well as the mechanical and creep behaviors of the resulting forged products. Additionally, SdF produced a prototype FB2 rotor using a conventional process. FB2, a 10% Cr steel containing cobalt and boron but lacking tungsten, emerged from the COST 522 program as the best candidate for scaling up from a laboratory experiment to a full-sized industrial component. Notably, the addition of boron effectively improved the microstructure's stability and consequently enhanced the creep resistance of these new, advanced martensitic steels. Finally, the paper will present updates on the long-term characterization program for the FB2 steel trial rotor.

The development of new ferritic-martensitic steels for rotor applications was a primary focus of the joint research projects COST 501 and COST 522. During COST 501, multiple trial compositions of 9-10% chromium steels underwent comprehensive testing, with the COST 522 project ultimately selecting the most promising candidate, FB2, a 10% Cr steel containing cobalt and boron additions, notably without tungsten. Società delle Fucine (SdF) successfully produced an FB2 prototype rotor using a conventional manufacturing process involving ladle furnace and vacuum degassing techniques. A comprehensive creep test program was initiated to characterize the full-size component's properties, with results demonstrating consistency with laboratory material performance in both creep resistance and ductility. The extensive testing, which exceeded 30,000 hours, aimed to achieve a 15-20 MPa improvement over Grade 92, targeting 100,000 creep hours at 600°C. Complementing the mechanical testing, a parallel microstructural investigation program was launched to evaluate structural evolution and gain deeper insights into boron's role as a creep-strengthening element in advanced ferritic-martensitic steels.

The T/P91 and T/P92 steel grades were developed as a result of a demand of high creep strength for advanced power plants. Nevertheless, their operating temperature range is limited by their oxidation performance which is lower compared with usual 12%Cr steels or austenitic steels. Moreover, the new designed power plants require higher pressure and temperature in order to improve efficiency and reduce harmful emissions. For these reasons, Vallourec and Mannesmann have recently developed a new 12%Cr steel which combines good creep resistance and high steam-side oxidation resistance. This new steel, with a chromium content of 12% and with other additional elements such as cobalt, tungsten and boron, is named VM12. Manufacturing of this grade has been successfully demonstrated by production of several laboratory and industrial heats and rolling of tubes and pipes in several sizes using different rolling processes. This paper summarizes the results of the investigations on base material, including creep tests and high temperature oxidation behavior, but also presents mechanical properties after welding, cold bending and hot induction bending.

Research conducted under European COST programs has demonstrated the beneficial role of boron in enhancing the microstructural stability and creep performance of new martensitic steels. The FB2 steel (a 10%Cr steel containing Co and B, without W) emerged as the most promising candidate and was successfully scaled up to a full industrial rotor component by Società delle Fucine. Extensive creep testing, now reaching 50,000 hours, indicates an improvement of 15-20 MPa over Grade 92 at 600°C for 100,000 hours. STEM and X-ray analysis of long-term aged specimens confirmed that boron significantly enhances precipitate stability compared to Grade 91 and 92 steels, validating its role as a creep-strengthening element and stabilizer of carbides and martensitic structure.

A thorough understanding of interactions between graphite and fluoride fuel salts is crucial, as graphite is a promising candidate for the moderator of molten salt reactors. This study investigates the infiltration of fluoride fuel salts into graphite and the fluorination of graphite by these salts under various pressures and temperatures. A high-pressure salt infiltration test apparatus was developed to examine the infiltration of NaF-KF-UF 4 and NaF-BeF 2 -UF 4 -ZrF 4 fuel salts into two types of graphite at high temperatures. For tests using NaF-BeF 2 -UF 4 -ZrF 4 , two different temperatures were selected to assess the impact of temperature on threshold pressure. The study observed salt infiltration into graphite at pressures exceeding its threshold pressure, and the threshold pressure for infiltration was lower at the higher temperature. In addition, the formation of carbon fluorides on the surface of post-test graphite specimens was identified.

Monoblock low-pressure (LP) turbine rotor shaft forgings for nuclear power plants have been produced from up to 600 ton ingots. However, ingots greater than 600 tons are necessary to increase the generator capacity. Segregation, non-metallic inclusions, and micro porosities inevitably increase with the increase in ingot size. Manufacturing such massive ingots with high soundness is quite difficult. Thus, the development of 650 ton ingot production was carried out in 2010. The 650 ton ingot was dissected and investigated to verify its internal quality. The internal quality of the 650 ton ingot was found to be equal to that of 600 ton ingots. Subsequently, in 2011, we produced a 670 ton ingot, the world’s largest, to produce a trial LP rotor shaft forging with a diameter of 3,200 mm. Results show that the internal quality, mechanical properties, and heat stability are the same as LP rotor shaft forgings made from 600 ton ingots.

Nickel-based Alloy 617B (DIN 2.4673) and Alloy C-263 (DIN 2.4650) with high creep strength and good fabricability are promising material candidates for the design of next generation coal-fired “Advanced Ultra-Super-Critical A-USC” power plants with advanced steam properties and thus higher requirements on the material properties. Microstructural studies of the precipitation hardened alloy C-263 were performed with Electron Microscopy (TEM) with respect to their strengthening precipitates like carbides and intermetallic gamma prime. Specimens were subjected to different ageing treatments at elevated temperatures for different times. The microstructural results of the investigated nickel alloy C-263 are presented and discussed with respect to their correlation with required properties for A-USC, e.g. the mechanical properties, the creep resistance and the high temperature stability and compared to Alloy 617B. The manufacturing procedure for the prematernal and forgings as well as for thin walled tube components for A-USC power plants is presented.

The manufacture of large, complex components for ultra-supercritical and oxy-combustion applications will be extremely costly for industry over the next few decades as many of these components will be manufactured from expensive, high strength, nickel-based alloys casting and forgings. The current feasibility study investigates the use of an alternative manufacturing method, powder metallurgy and hot isostatic processing (PM/HIP), to produce high quality, and potentially less expensive components for power generation applications. Benefits of the process include manufacture of components to near-net shapes, precise chemistry control, a homogeneous microstructure, increased material utilization, good weldability, and improved inspectability.

Alloy 718, widely used for its high-temperature performance in various applications, is being investigated for use in advanced power plants. Driven by the need for efficiency improvements, these plants demand higher temperatures and pressures, putting significant stress on critical components like boiler tubes and turbines. With existing steels and alloys struggling at such high temperatures, researchers are exploring alternatives. New generation plants target steam turbine inlet temperatures of 720°C and pressures of 350MPa, necessitating superalloys for high- and intermediate-pressure rotor sections. The Thermie Advanced project explored the potential of 718 for these applications. A trial rotor disk, forged using advanced processes, underwent a novel heat treatment to enhance microstructural stability and improve creep behavior. Ongoing creep tests exceeding 100,000 hours suggest a potential 50°C increase in the operational limit compared to standard 718. This 12-year research effort holds promise for utilizing 718 in forged components of advanced ultra-supercritical power plant steam turbines, potentially operating up to 700°C.

The increasing steam parameters in modern high-efficiency fossil fuel power plants demand advanced materials with enhanced creep strength for operation under extreme temperature and pressure conditions. Tenaris has focused on developing ferritic-martensitic and austenitic grades for tube and pipe applications. At TenarisDalmine, efforts on ferritic-martensitic steels include ASTM Grade 23, a low-alloyed alternative to Grade 22 with 1.5% W, offering good weldability, creep resistance up to 580°C, and cost competitiveness. Additionally, ASTM Grade 92, an improved version of Grade 91, provides high creep strength and long-term stability for components like superheaters and headers operating up to 620°C. At TenarisNKKT R&D, austenitic steel development includes TEMPALOY AA-1, an improved 18Cr-8NiNbTi alloy with 3% Cu for enhanced creep and corrosion resistance, and TEMPALOY A-3, a 20Cr-15Ni-Nb-N alloy with superior creep and corrosion properties due to its higher chromium content. This paper details the Tenaris product lineup, manufacturing processes, and key material properties, including the impact of shot blasting on the steam oxidation resistance of austenitic grades. It also covers ongoing R&D efforts in alloy design, creep testing, data assessment, microstructural analysis, and damage modeling, conducted in collaboration with Centro Sviluppo Materiali.

Advanced chromium-molybdenum-vanadium steels 9CrMoV [P(T)91] have seen extensive global adoption across power, petrochemical, and other industrial sectors over the past decade, driven by the demand for materials with superior high-temperature properties to improve efficiency. Experience with P(T)91 base metals and weldments has revealed that these steels require substantially more attention than the commonly used P(T)22 grade and similar materials. This presentation examines Grade 91's various design code requirements across power, petroleum, and nuclear industries, focusing on fabrication and welding considerations. The discussion covers critical material properties and heat treatment parameters, including the significance of maintaining proper preheat and interpass temperatures, while highlighting the risks associated with interrupted heating cycles and improper postweld heat treatment. The paper also addresses factors influencing the use, development, and procurement of Modified Grade 91 welding consumables for heavy wall applications, and explores the subtle technical differences between North American and European approaches to production and utilization, ultimately emphasizing the considerable care required during joining processes to ensure acceptable long-term properties.

Martensitic 9Cr steels have been developed which are strengthened by boron in order to stabilize the microstructure and improve their long-term creep strength. Boron plays a key role in these steels by stabilising the martensitic laths by decreasing the coarsening rate of M 23 C 6 carbides, which act as pinning points in the microstructure. In this work two modified FB2 steel forgings are compared. Both forgings have similar compositions but one underwent an additional remelting process during manufacture. Creep tests showed that this additional processing step resulted in a significant increase in time to failure. In order to investigate the effect of the processing route on microstructural evolution during aging and creep, a range of advanced electron microscopy techniques have been used including ion beam induced secondary electron imaging and High Angle Annular Dark Field (HAADF) imaging in the Scanning Transmission Electron Microscope. These techniques have enabled the particle population characteristics of all the second phase particles (M 23 C 6 , Laves phase, BN and MX) to be quantified for materials from both forging processes. These quantitative data have enabled a better understanding of how the processing route affects the microstructural evolution of FB2 steels.