Search Results for small punch creep test

There is an increased interest in miniature testing to determine material properties. The small punch test is one miniaturized test method that has received much interest and is now being applied to support the design and life assessment of components. This paper presents the results of a test program for a small punch creep test at 650°C of 316L stainless steel produced from additive manufacturing. A major finding is that the deflection rate curve versus time may have multiple minima as opposed to forged 316L with only one minimum. This is believed to be due to microcracking and has direct consequences on the determination of the creep properties that that are based on a single minimum value in the CEN Small Punch Standard. In the paper, aged and nonaged materials are compared, and small punch creep results are also compared with standard uniaxial creep tests. The multiple minima feature means that the approach to determine equivalent stress and strain rate from the minimum deflection rate needs to be modified. Some approaches for this are discussed in the paper. Under the assumption that the multiple minima represent cracking, it opens up opportunities to quantify reduced creep ductility by the small punch test.

A trial weld joint of COST F and COST FB2 steels was produced using the GTAW HOT-WIRE method in conditions used in industry for production of welding steam turbine rotors. Conventional long-term creep tests (CCT) to the rupture of this weldment and the base materials were carried out at temperatures ranging from 550 °C to 650 °C in the stress range from 70 to 220 MPa (the longest time to rupture was above 52,000 hours). Creep rupture strength was evaluated using Larson-Miller parameter model. Assessment of microstructure was correlated with the creep strength. Precipitation of Laves phase and structure recovery during creep exposures were the main reasons for the failure which occurred in the heat affected zone of steel COST F. The recently developed simulative accelerated creep testing (ACT) on thermal-mechanical simulator allows the microstructural transformation of creep-resisting materials in a relatively short time to a state resembling that of multiyear application under creep conditions. ACT of samples machined from various positions in the weldment was performed at 600 °C under 100 MPa. Changes in the hardness and the microstructures of the samples, which underwent both types of creep tests, were compared. Small sample creep test (SPCT), another alternative method how to obtain information about the creep properties of materials when only a limited amount of test material is at disposal, were performed. It was shown that the same stress-temperature dependence and relationships are valid in the SPCT as in the CCT. Using a simple load-based conversion factor between the SPCT test and the CCT test with the same time to rupture, the results of both test types can be unified.

Remaining-life assessment of high temperature components using the small punch (SP) creep testing technique necessitates the evaluation of SP load (F)/uniaxial stress (σ) conversion factor, F/σ, obtained by comparing the SP and uniaxial creep test results. In the present study, the SP creep tests were carried out at 850°C on various Ni-base alloys having different reduction of area in the range of 0.05-0.67 to investigate the influence of creep ductility on the value of F/σ. The F/σ value was determined for each alloy by correlating SP creep rupture data with corresponding uniaxial creep ones. The experimental results revealed that the F/σ value was not well correlated with Vickers hardness, but it increased almost linearly with increasing reduction of area up to around 0.4. This result indicated that the SP creep rupture data could be converted to the uniaxial data if the creep ductility on a given material was available.

Small punch creep testing (SPCT) is a small-scale, accelerated creep test that allows for the determination of creep data using a limited amount of material. The question, however, remains how the data generated by this technique correlate to more established techniques such as uniaxial testing and ultimately to predictions regarding the remaining service life of a plant component. This empirical study investigated the microstructure-to-property relationship of welded 9-12%Cr steels as measured using SPCT. Virgin P91 (X10CrMoVNb9-1) steel was joined to service exposed X20 (X20CrMoV12-1) steel using two different filler materials (X20 and P91) via fusion welding. Site-specific samples were extracted from the parent plates, heat affected zones and weld metals using electro-discharge machining. Small punch creep testing were performed using a 276 N load at a temperature of 625°C. The untested sample microstructures were quantitatively characterized using a range of electron microscopy techniques to determine the precipitate (M 23 C 6 , MX) spacing, subgrain sizes and dislocation densities for each region of the weldments. Multiple linear regression analysis found that the subgrain size (λsg) played the largest contribution to the SPCT rupture life. The heat affected zones had the lowest SPCT rupture times (49-68 hours), which corresponded to the largest subgrain sizes (1.1-1.3 μm). The P91 parent plate material had the longest SPCT rupture time (349 hours), which corresponded to the lowest subgrain size (0.8 μm). The P91 weld metal sample showed lower initial deflection rates during the SPC testing, however the presence of non-metallic SiO 2 inclusions in this zone contributed to accelerated brittle failure.

The small punch (SP) test technique can generate tensile, toughness, and creep strength data from very small specimens, enabling nondestructive sampling from large components. This has accelerated industry interest in SP, particularly in the energy sector. A round-robin for the SP creep test was organized within the EPERC network on a 1CrMoV rotor steel, primarily to contribute to harmonizing the test procedure for this emerging method. This presentation analyzes the SP creep test results performed at several temperatures and one load level to assess their inter-comparability and interpret the results concerning conventional uniaxial creep tests. The SP loading geometry appeared to be a key parameter in evaluating the SP results, particularly for correlation with uniaxial creep behavior. A standardization initiative for the SP test method, including creep as well as low-temperature testing for determining tensile and toughness properties of metallic materials, has recently started via a CEN Workshop.

A prototype small punch test rig has been developed to extend the range of data output. Through the introduction of a probe, vertical displacements can be measured across a region of the specimen underside. This information provides much greater understanding of the specimen deformation. Having displacement data at a series of measurement points also facilitates the calculation of strains across the sample. The probe can also be used during a test to provide time dependent data from small punch creep tests. The measured displacement data have been used in conjunction with FE analysis to determine a set of calibration curves for inferring strain at any given vertical displacement. Some creep strain data are also presented.

A new method of creep life assessment was developed to consider heat-to-heat variations of welded joints of materials used in power plants. This paper explains a scheme of the assessment method and also describes an actual implementation of the method for Grade 91 steel. In the method, creep properties of the welded joints are related to those of each base metal because the heat-to-heat variations of welded joints strongly depend on the creep properties of the corresponding base metals. To estimate the creep properties of each base metal of the target pipe, microstructure analyses and small punch creep tests were conducted using small samples cut from the base metals in service, and evaluations were done on the basis of material data base obtained using standard test samples of long-term service exposed pipes. It is expected that the precision of the life assessment of pipes will be significantly improved using the developed method because it can consider the heat-to-heat variations of their materials, which are not considered in existing life assessment methods.

Components such as tubes, pipes and headers used in power generation plants are operated in a creep regime and have a finite life. During partial replacement, creep exhausted materials are often welded to virgin materials with superior properties. The aim of this study was to identify a suitable weld filler material to join creep aged X20CrMoV12-1 to a virgin P91 (X10CrMoVNbV9-1) steel. Two dissimilar joints were welded using the gas tungsten arc welding (GTAW) process for the root passes, and manual metal arc (MMA) welding for filling and capping. The X20 and the P91 fillers were selected for joining the pipes. The samples were further heat treated at 755°C to stress relief the samples. Microstructural evolution and mechanical properties of the weld metals were evaluated. The average hardness of X20 weld metal (264 HV10) was higher than the hardness measurement of P91 weld metal (206 HV10). The difference in hardness was attributed to the high carbon content in X20 material. The characterisation results revealed that the use of either X20 or P91 weld filler for a butt weld of creep aged X20 and virgin P91 pipes material does not have a distinct effect on the creep life and creep crack propagation mechanism. Both weld fillers (X20 and P91) are deemed to be suitable because limited interdiffusion (<10 μm) of chromium and carbon at the dissimilar weld interface was observed across the fusion line. The presence of a carbon ‘denuded’ zone was limited to <10 μm in width, based on the results from local measurements of the precipitate phase fractions using image analysis and from elemental analysis using EDS. However the nanoindentation hardness measurements across the fusion line could not detect any ‘soft’ zone at the dissimilar weld interface. The effect of the minute denuded zone was also not evident when the samples were subjected to nanoindentation hardness testing, tensile mechanical testing, Small Punch Creep Test (SPCT) and cross weld uniaxial creep testing.

Recently advanced ultra-super critical (A-USC) pressure power plants with 700°C class steam parameters have been under development worldwide. Japanese material R&D program for A- USC beside the plant R&D program started in 2008, launched in 2007 under the METI/NEDO foundation includes not only alloy design explores and novel ideas for developing new steels and alloys that can fill critical needs in building 700°C class advanced power plants, but also fundamental studies on creep strength and degradation assessment, which are absolutely needed to assure the long-term safe use of newly developed steels and alloys at critical temperature conditions, for instance, 650°C for ferritic steels, 700°C for austenitic steels and 750°C for Ni- based alloys. This program concept has been based on the lessons from materials issues recently experienced in the creep strength enhanced ferritic steels used for 600°C class ultra-super critical power plants. Particular outputs from the program up to now are recognized as the ferritic steel having the creep strength of 100MPa at 650°C beyond 30,000h without any Type IV degradation and as the austenitic steel developed by means of inter-metallic compounds precipitation strengthening of grain boundary which should be strongest in creep ever found. Concurrently great progresses have been seen in the research works with positron annihilation life monitoring method applicable to various kinds of defects, structural free energy values, small punch creep test data for very limited interest area, crystallographic analyses, optimum time-temperature parameter regional creep rupture curve fitting method, hardness model, etc. which would highly contribute to find out and establish the structural parameters affecting to creep strength and degradation resulting in accurately estimating the 100,000h creep strength.

This paper investigates the effect of high temperature tensile strain on subsequent creep strength in grade 91 steel. Failed hot tensile specimens have been sectioned at various positions along the specimen axis, and therefore at different levels of hot tensile strain, to obtain material for creep strength evaluation. Because of the limited amount of material available for creep testing obtained in this way, creep testing has been carried out using the specialised small-scale impression creep testing technique. The grade 91 material has been tested in both the normal martensitic condition and in an aberrant mis-heat treated condition in which the microstructure is 100% Ferrite. The latter condition is of interest because of its widespread occurrence on operating power plant with grade 91 pipework systems.

The effect of taking miniature sample scoops on the creep life of ASME Grade 91 steel pipes was experimentally and analytically assessed in this work. Internal pressure tests were conducted on tubular specimens having defects on their outer surface, which simulate sampling scoops. The creep life did not decrease until the depth ratio of the defect to the wall thickness of the specimens was about 5%, and the creep life decreased with increasing defect depth when the depth ratio exceeded about 5%. When the depth ratio was about 11%, the creep life decreased to four-fifths of that of a specimen with no defects. In addition, as a result of investigating the stress concentration around a defect with a depth ratio of about 5% by the finite element method, stress concentration was clearly observed around the defect. These results suggest that taking a miniature sample up to a depth of 5% of the thickness of a Grade 91 steel pipe in service has a negligible effect on the creep life of the pipe.

This paper presents the CEN WS064 Prospective Group 2, a project involving different European stakeholders from more than 20 organizations with the objective to identify the needs and propose code developments research for the nuclear design and construction code RCC-MRx for innovative reactors with more onerous operational conditions: i) reactor components are generally exposed to higher temperatures; ii) have innovative and more corrosive coolants such as liquid lead or molten salt; iii) materials and components are generally exposed to higher radiation levels than light-water reactors. The main outputs of the CEN WS064 are code evolution proposals and proposals for pre-normative research in support of code evolution. The code evolution is driven by further improving safety and cost reduction. Nuclear Design Codes are robust engineering tools but should incorporate new technologies and research. The paper describes the adopted methodology and the rationale for identifying code evolution needs. Code evolution and research proposals will be discussed. Examples of proposals that will be discussed include: Guideline for design of material/components with innovative coolants, extension of design life to 60 years; qualification of new materials and components with advanced manufacturing. A general requirement is that code evolution and associated material and component qualification and codification need to be significantly accelerated for which new approaches such as AI tools will play an important role.

The impression creep test method using a rectangular indenter has been well established and the applicability of the technique has been supported by the test data for a number of metallic materials at different temperatures and stresses. The technique has proved to be particularly useful in providing material data for on-site creep strength assessments of power plant components operating in the creep regime. Due to these reasons, “standard” assessment procedures using the impression testing method are needed in order for the technique to be more widely used. This paper will first address some key issues related to the use of the impression creep test method, involving the data conversion method, typical test types and validity of the test technique etc. Then some recommendations on a number of practical aspects, such as the basic requirements of test rigs, “standard” specimen geometry, indenter dimensions, sampling procedures for scoop samples, specimen preparation, temperature and loading control, and displacement measurement, are briefly addressed. Finally, applications of the test data to assist with the risk management and life assessment programme of power plant components, particularly those with service-exposed materials, using data obtained from scoop samples, are described. Proposals for future exploitation and for improvement of the technique are addressed.

In today’s market place power generation plants throughout the world have been trying to reduce their operating costs by extending the service life of their critical machines such as steam turbines and gas turbines beyond the design life criteria. The key ingredient in plant life extension is remaining life assessment technology. This paper will outline remaining life procedures which will incorporate the defect tolerant design concepts applied to the various damage mechanisms such as creep, fatigue, creep-fatigue and stress corrosion cracking. Also other embrittlement mechanisms will also be discussed and how they will influence the life or operation of the component. Application of weld repairs to critical components such as rotors and steam chest casings will be highlighted and how defect tolerant design concept is applied for the repair procedure and the acceptance standard of the nondestructive testing applied. Also highlighted will be various destructive tests such as stress relaxation tests (SRT) which measures creep strength and constant displacement rate test (CDRT) which evaluates fracture resistance or notch ductility. Also shown will be actual life extension examples applied to steam turbine components and weld repairs. Utilization of computer software to calculate fatigue and creep fatigue crack growth will also be presented

A new martensitic steel for power generation applications was developed: Tenaris High Oxidation Resistance (Thor) is an evolution of the popular ASME grade 91, offering improved steam oxidation resistance and better long-term microstructural stability, with equal or better creep strength. Thanks to its design philosophy, based on consolidated metallurgical knowledge of microstructural evolution mechanisms, and an extensive development performed in the last decade, Thor was engineered to overcome limitations in the use of ASME grade 91, yet allow being processed in the same fashion, permitting the re-use of consolidated best practices for boiler fabrication. In order to evaluate the possibility to produce complete pressure part systems, various tests to manufacture components have been performed on Thor pipes and tubes (i.e. finning, bending, welding) and on Thor forged material (i.e. flanges). In all cases consolidated industrial best practices used on ASME grade 91 were applied, and resulting properties met ASME requirements.

There is a constant need for improved knowledge of the influence of non-standard processing on the expected performance of creep strength enhanced ferritic (CSEF) materials as the total installed tonnage of these materials is rapidly increasing across the power generation industry. Cr-Mo-V steel grades micro-alloyed with niobium and titanium designed for pressurized equipment operating in the supercritical steam range proved to be very sensitive to relative minor variations in the principal heat treatment parameters time and temperature, when compared to the traditional Cr-Mo-V grades. A key component for successful welds is optimised post weld heat treatment (PWHT). Under certain conditions premature failures of welds can occur when incorrect weld and heat treatment performance result in a reduction of specified mechanical properties and high temperature creep performance, it is therefore of significant importance to have a good understanding of actual material properties for effective operation and plant life studies. This study investigated the effect and impact variations of post weld heat treatment time and temperature on mechanical properties of tungsten inert gas (TIG) and manual metal arc (MMA) welds on Grade 91 pipes from a set of reference samples. This is in preparation of establishing a benchmark set of tests to determine the integrity and expected long-term performance of butt-welds from limited site sample volumes, providing a non-intrusive methodology to identify welds suspected to have received non-standard PWHT cycles on Grade 91 pipework systems.

INCONEL alloy 740H has been specified for tube and pipe for the boiler and heat exchanger sections of AUSC and sCO 2 pilot plants currently designed or under construction. These systems also require fittings and complex formed components such as flanges, saddles, elbows, tees, wyes, reducers, valve parts, return bends, thin-wall cylinders and tube sheets. The initial evaluation of alloy 740H properties, leading to ASME Code Case 2702, was done on relatively small cross-section tube and plate. The production of fittings involves the use of a wide variety of hot or cold forming operations. These components may have complex geometric shapes and varying wall thickness. The utility industry supply chain for fittings is largely unfamiliar with the processing of age-hardened nickel-base alloys. Special Metals has begun to address this capability gap by conducting a series of trials in collaboration with selected fittings manufacturers. This paper describes recent experiences in first article manufacture of several components. The resulting microstructure and properties are compared to the published data for tubular products. It is concluded that it will be possible to manufacture most fittings with properties meeting ASME Code minima using commercial manufacturing equipment and methods providing process procedures appropriate for this class of alloy are followed. INCONEL and 740H are registered trademarks of Special Metals Corporation.

Recovery of microstructure and void formation were investigated in creep-ruptured specimens of ASME Gr. T91 steels to understand the cause of loss of creep rupture ductility in the long-term creep condition and its heat-to-heat variation. The specimens studied were two heats (MGA, MGC) of Gr. T91 steels creep-ruptured at 600 °C under the stress conditions of 160-80 MPa. The reduction of area at rupture (RA) was 55% for MGA, but 83% for MGC in the long-term condition (under the creep stress of 80 MPa), while RA was higher than 80 % for the two heats in the short-term conditions (under the creep stresses above 100 MPa). In both heats, equiaxed grains were observed in the vicinity of ruptured surface in the long-term condition, indicating that recovery and recrystallization occurred extensively in the creep condition, while grains were elongated in the short-term conditions. In the uniformly deformed regions with a small area reduction in the long-term crept specimens, recovered and recrystallized grains were observed in the limited region close to high angle grain boundaries in MGA, while they were extended into grain interiors in MGC. In the long-term creep conditions two types of voids were observed: fine ones with a diameter below 1 μm and coarse ones with a diameter from 2 μm up to 50 μm. Fine creep voids were found to grow with necking in MGA while they neither nucleated nor grew with necking in MGC. Coarse creep voids increased in size and in number with necking in both heats and were larger and denser in MGA than in MGC.

The microstructures and mechanical properties of T122 steel used for superheater tube of the boiler in a 1000 MW ultra supercritical power plant after service for 83,000h at 590℃ were investigated, and compared with data of that served for 56,000h in previous studies. The results show that compared with T122 tube sample service for 56,000h, the tensile properties at room temperature and the size of precipitated phase exhibit few differences, but the lath martensites features are apparent, and the Brinell hardness value are obviously higher. SEM and TEM experiments show that the substructure is still dominated by lath martensite. A few lath martensites recover, subgrains appear and equiaxe, and the dislocation density in grains is relatively low. A large number of second-phase particles precipitated at boundaries of original austenite grains and lath martensite phases, which are mainly M 23 C 6 and Laves phases.

The A286 is one of the earliest superalloys developed. It has been used for manufacturing different components of turbo machineries because of its balanced high temperature properties. These components include shafts, discs, spacers, blades and fasteners. This paper reviews some of the issues and recent field experiences related to metallurgy, fabrication, in-service evaluation and failure of some of these components. The fabrication aspects including the effects of alloy melting processes, forging parameters and different types of heat treatments on the processed parts are discussed. The importance of these factors on the microstructure and properties of A286 are highlighted. The effects of service exposure on some of these parts are also discussed. In service evaluation involves checking for service induced damage or changes in microstructures and properties so that the suitability of the part for continued service can be determined. The failure analysis section of the paper briefly discusses failures of two expander wheels and an expander disc made out of A286 to pinpoint some of the salient features of damage accumulation and fracture during service.