Search Results for nickel-chromium alloys

The INCONEL filler metals 72 and 72M have been utilized significantly for weld overlay protection of superheaters and reheaters, offering enhanced corrosion and erosion resistance in this service. Laboratory data conducted under simulated low-NOx combustion conditions, field exposure experience, and laboratory analysis (microstructure, chemical composition, overlay thickness measurements, micro-hardness) of field-exposed samples indicate that these overlay materials are also attractive options as protective overlays for water wall tubes in low-NOx boilers. Data and field observations will be compared for INCONEL filler metals 72, 72M, 625 and 622.

Ductility dip cracking (DDC) is known to occur in highly restrained welds and structural overlays made using high chromium (Cr) nickel (Ni) based filler metals in the nuclear power generation industry, resulting in costly repairs and reworks. Previous work explored the role of mechanical energy imposed by the thermo-mechanical cycle of multipass welding on DDC formation in a highly restrained Alloy 52 filler metal weld. It was hypothesized that imposed mechanical energy (IME) in the recrystallization temperature range would induce dynamic recrystallization (DRX), which is known to mitigate DDC formation. It was not shown however that IME in the recrystallization temperature range (IMERT) induced DRX. The objective of the work is to discern if a relationship between IMERT and DRX exists and quantify the amount of DRX observed in a filler metal 52 (FM-52) groove weld. DRX was analyzed and quantified using electron beam scattered diffraction (EBSD) generated inverse poll figures (IPF), grain surface area and grain aspect ratio distribution, grain orientation spread (GOS), kernel average misorientation (KAM), and grain boundary (GB) length density. From the analysis, GOS was determined to be an unsuitable criterion for quantifying DRX in multipass Ni-Cr fusion welds. Based on the observed criteria, higher IMERT regions correlate to smaller grain surface area, larger grain boundary density, and higher grain aspect ratio, which are all symptoms of DRX. High IMERT has a strong correlation with the symptoms DRX, but due to the lack of observable DRX, creating a threshold for DRX grain size, grain aspect ratio, and GB density is not possible. Future work will aim to optimize characterization criteria based on a Ni-Cr weld with large presence of DRX.

The U.S. Department of Energy (DOE) and the Ohio Coal Development Office (OCDO) are sponsoring the “Boiler Materials for Ultrasupercritical Coal Power Plants” program. This program is aimed at identifying, evaluating, and qualifying the materials needed for the construction of critical components for coal-fired boilers capable of operating at much higher efficiencies than the current generation of supercritical plants. Operation at ultrasupercritical (USC) conditions (steam temperatures up to 760°C (1400°F)) will necessitate the use of new advanced ferritic materials, austenitic stainless steels and nickel-based alloys. As well as possessing the required mechanical properties and fireside corrosion resistance, these materials must also exhibit acceptable steamside oxidation resistance. As part of the DOE/OCDO program, steamside oxidation testing is being performed at the Babcock & Wilcox Research Center. More than thirty ferritic, austenitic and nickel-based materials have been exposed for up to 4,000 hours in flowing steam at temperatures between 650°C (1202°F) and 800°C (1472°F). In addition to wrought materials, steamside oxidation tests have been conducted on weld metals, coated materials and materials given special surface treatments. Exposed specimens were evaluated to determine oxidation kinetics and oxide morphology. High chromium ferritic, austenitic and nickel-based alloys displayed very good oxidation behavior over the entire temperature range due to the formation of a dense chromium oxide. With increasing steam temperature, low chromium ferritic materials experienced breakaway oxidation, and low chromium austenitic materials experienced significant oxide exfoliation. Special surface treatments that were applied to these materials appeared to have a beneficial effect on their oxidation behavior.

Nitridation is a high-temperature material degradation issue that can occur in air and in environments containing nitrogen, ammonia, etc., and in a variety of industrial processes. The nitridation behavior of several commercial nickel- and cobalt-based alloys is reviewed in this paper. The alloys include Haynes 230, Haynes 188, Haynes 625, Haynes 617, Haynes 214, Hastelloy X, and Haynes 233. The environments discussed are high-purity nitrogen gas between 871°C and 1250°C, 100% ammonia gas at 982°C and 1092°C, and a simulated combustion atmosphere at 982°C. The results showed that nitridation occurred in all the environments containing nitrogen. The nitridation attack was strongly influenced by the alloy compositions and the type of oxide formed (i.e., chromia or alumina), as some degree of oxidation was expected in the environments in which residual oxygen was present. Thermal cycling is briefly discussed because the integrity of protective oxides is also an important factor in resisting high-temperature oxidation and nitridation attack.

Nickel-base alloys were exposed to flowing supercritical CO 2 (P = 20MPa) at temperatures of 700 to 1000°C for up to 1000 h. For comparison, 316L stainless steel was similarly exposed at 650°C. To simulate likely service conditions, tubular samples of each alloy were internally pressurised by flowing CO 2 , inducing hoop stresses up to 35 MPa in the tube walls. Materials tested were Haynes alloys 188, 230 and 282, plus HR120 and HR160. These alloys developed chromia scales and, to different extents, an internal oxidation zone. In addition, chromium-rich carbides precipitated within the alloys. Air aging experiments enabled a distinction between carburisation reactions and carbide precipitation as a result of alloy equilibration. The stainless steel was much less resistant to CO 2 attack, rapidly entering breakaway corrosion, developing an external iron-rich oxide scale and internal carburisation. Results are discussed with reference to alloy chromium diffusion and carbon permeation of oxide scales.

The pursuit of reduced emissions and increased efficiency in ultra-critical steam plants has led to the investigation of systems operating at temperatures up to 720°C and pressures up to 300 bars, necessitating the use of nickel-based alloys. This study focuses on control valves manufactured from Alloy 617, designed for steam temperatures of 725°C, examining specific challenges in their design and manufacture, including machining and welding processes. Initial operational experiences with the valve at 725°C are presented, along with ongoing tribological investigations of nickel-based alloys at 725°C, as standard material pairings with optimized wear behavior are unsuitable at such elevated temperatures. These investigations aim to develop material pairings that can maintain good wear behavior under these extreme conditions.

Coal ash corrosion testing was conducted on six solution-treated nickel-based alloy plates (Alloy 617, Alloy 263, Alloy 740, Alloy 141, HR6W [45Ni-23Cr-7W], and HR35 [50Ni-30Cr-4W-Ti]) intended for advanced-USC boilers, along with conventional ferritic and austenitic stainless tubes for comparison. Tests used synthetic coal ash (Na 2 SO 4 , K 2 SO 4 , Fe 2 O 3 ) with varying SO 2 concentrations (0.02-1.00 vol%). Results showed maximum metal loss at 700°C, with higher SO 2 levels causing increased corrosion. Materials with higher chromium content demonstrated better corrosion resistance, suggesting chromium content is a crucial factor in material selection for these applications.

Model alloys of Fe-20Cr and Ni-20Cr (all compositions in weight %) and variants containing small amounts of Si or Mn were exposed to Ar-20CO 2 and Ar-20CO 2 -H 2 O (volume %) at 650 or 700°C. Protective Cr 2 O 3 scale was more readily formed on Fe-20Cr than Ni-20Cr, as a result of the different alloy diffusion coefficients. Silicon additions slowed chromia scale growth, promoting passivation of both alloy types. Water vapour accelerated chromia scaling, but slowed NiO growth.

As part of the Boiler Materials for Ultrasupercritical Coal Power Plants program, sponsored by the United States (U.S.) Department of Energy (DOE) and the Ohio Coal Development Office (OCDO), the steamside oxidation and oxide exfoliation behavior of candidate alloys have been thoroughly evaluated in steam at temperatures between 620°C and 800°C (1148°F and 1472°F) for times up to 10,000 hours. The results from this test program indicate that the oxidation rates and oxide morphologies associated with steamside oxidation are a strong function of the crystallographic lattice structure and the chromium content of the material. Oxide exfoliation correlates to oxide thickness. The time required to reach the critical oxide thickness for exfoliation can be estimated based on oxidation kinetic relationships. For austenitic stainless steels, shot peening is effective in reducing steamside oxidation/exfoliation, but the efficacy of this technique is limited by the operating temperature. Nickel-based alloys exhibit very low oxidation/exfoliation rates, but have a propensity to form aluminum/titanium oxides along near surface grain boundaries.

Improving power plant efficiency through supercritical steam pressures and very high steam temperatures up to 700°C and beyond is an effective approach to reducing fuel consumption and CO2 emissions. However, these extreme steam temperatures necessitate the use of nickel-base alloys in the high-pressure/intermediate-pressure turbine sections requiring very large component sections that cannot be met by steels. Saarschmiede, involved in manufacturing large components for the power generation industry and research programs on advanced 9-12% chromium steels, has extensive experience producing nickel and cobalt-base alloy forgings for applications like aircraft engines, aerospace, land-based gas turbines, and offshore. This paper reports on the manufacturing and testing of large-section forgings made from candidate nickel-base alloys like 617 and 625 for high-pressure/intermediate-pressure turbine components in power stations operating at 700°C and higher steam temperatures.

Utilities worldwide are facing increased demand for additional electricity, reduced plant emissions and greater efficiency. Part of the solution is achieved by increasing boiler temperature, pressure and coal ash corrosion resistance of the materials of boiler construction. In this paper, a new nickel-base tube alloy, INCONEL alloy 740, meeting this challenge is characterized with emphasis on mechanical properties, coal ash and steam corrosion resistance as well as weldability. Microstructural stability as a function of temperature and time is addressed as well as some of the early methodology employed to arrive at the current chemical composition. Brief mention is made of certain current and future alloy characterization efforts and potential environmental benefits to be expected should the boiler technology utilizing INCONEL alloy 740 be adopted.

High efficiency in power generation is not only desirable because of economical reasons but also for enhanced environmental performance meaning reduced quantity of forming ash and emissions. In modern medium to large size plants, improvements require supercritical steam values. Furthermore, in future there will be an increasing share of renewables, such as wind and solar power, which will enhance the fluctuation of supply with the consequence that other power sources will have to compensate by operating in a more demanding cyclic or ramping mode. The next generation plant will need to operate at higher temperatures and pressure cycles coupled with demanding hot corrosion and oxidation environments. Such an operation will significantly influence the performance of materials used for boilers and heat exchanger components by accelerating oxidation rates and lowering mechanical properties like creep resistance. The paper discusses the oxidation behaviour of San25, 800H and alloy 263 in supercritical water at temperatures 650 and 700 °C at 250 bar, and compares the changes of mechanical properties of materials at these temperatures.

SMST is producing Ni alloy Boiler tubes since more than 10 years with application in several test loops and R&D programs. This paper will give an overview about the experience with the common grades A617 as well as C263 plus some additional information on the new developed austenitic material “Power Austenite MoW”.

In the late 1980s, the domestic utility industry experienced failures in dissimilar metal welds (DMWs) between low-alloy ferritic tubing and austenitic tubing in superheaters and reheaters. Extensive research by EPRI found that nickel-based filler metals provided significant service life improvements over 309 stainless steel filler metals. Improved joint geometries and additional weld metal reinforcement were determined to extend service life further. A new nickel-based filler metal was also developed, exhibiting thermal expansion properties similar to the low-alloy base metal and a low chromium content that would result in a smaller carbon-depleted zone than currently available fillers. However, this new filler metal was never commercialized due to a tendency for microfissuring, resulting in less than desired service life. This paper discusses further investigation into the filler metal microfissuring issue and examines long-term testing to determine the filler's suitability for high-temperature applications.

Cast nickel-based superalloys used as structural materials for gas turbine parts need to withstand high temperatures and dynamic mechanical loads. When in contact with ambient air, the formation of protective oxide scales causes a depletion of γ’-precipitates in the surface-near region and leaves a weakened microstructure. This environmentally based degradation of the material might be accelerated under cyclic thermal exposure. In this paper, the cyclic oxidation behavior of two cast nickel-based superalloys and one single crystalline variant are investigated: C1023, CM-247 LC and M-247 SX. Exposure tests were carried out under both isothermal and cyclic conditions in air at 850 °C, 950 °C and 1050 °C for times up to 120 h to investigate the impact of thermal cycling. The differences in oxidation mechanisms are analyzed phenomenologically via light and electron microscopy and brought in correlation with the oxidation kinetics, determined based on net mass change and depletion zone growth. An assessment of the impact of precipitation loss on local mechanical strength is attempted via nano-indentation method. The found relations can be transferred onto an acceleration of crack growth under creep-fatigue and thermo-mechanical fatigue conditions.

A collaborative program by the U.S. Department of Energy and Ohio Coal Development Office aims to identify new materials for ultrasupercritical (USC) coal power plants operating at significantly higher efficiencies. These USC plants require advanced ferritic alloys, austenitic steels, and nickel-based alloys with superior steamside oxidation resistance at high temperatures (up to 800°C). Initial tests on over 20 candidate materials exposed to flowing steam at 650°C for 4,000 hours show promise for nickel-based and austenitic alloys, while highlighting the dependence of oxidation resistance on chromium content for ferritic alloys. Notably, even within 9% Cr ferritic steels, varying compositions resulted in significantly different oxidation behaviors.

Tests show that Inconel Filler Metal 72 overlay and/or Incoclad alloys 671/800HT are two material solutions that will provide adequate corrosion and erosion protection for superheater and reheater tubes in low-NOx boilers. This paper gives an overview of the corrosion issues involved in these applications and presents test data for these materials.

Inconel alloy 740, a precipitation-hardenable nickel-chromium-cobalt alloy with niobium addition, has emerged as a leading candidate material for ultra-supercritical (USC) boilers due to its superior stress rupture strength and corrosion resistance at operating temperatures near 760°C. While derived from Nimonic alloy 263, alloy 740's unique chemistry necessitates comprehensive weldability studies to address potential challenges including heat-affected zone liquation cracking, ductility-dip cracking, and post-weld heat treatment cracking. This ongoing investigation examines the alloy's weldability characteristics through material characterization studies comparing its cracking sensitivity to established aerospace alloys like Waspalloy and Inconel alloy 718. The research applies aerospace industry expertise to boiler applications requiring sections up to three inches thick, with gas tungsten arc welding and pulsed gas metal arc welding identified as the most promising processes for producing sound, crack-free welds.

The article gives a brief overview of the newly developed austenitic material “Power Austenite”. The microstructure of the Power Austenite is characterized by grain boundary strengthening with boron stabilized M23(C,B)6 and secondary Nb(C,N) in combination with sigma phase and Nb(C,N) as the major grain strengthening precipitates. The material shows a significant creep strength at 700 °C (1292 °F) and 650 °C (1202 °F) as well as fireside corrosion resistance which makes it a possible candidate for 700 °C (1292 °F) power plants.

Materials are the key to develop advanced ultra-supercritical (A-USC) steam generators. Operating at temperature up to 760°C and sustained pressure up to 4500 psi. Pressure vessel and piping materials may fail due to creep, oxidation, and erosion. Valves are particularly subjected to loss of function and leakage due to impermeant of the sealing surfaces. New materials, less susceptible to the above damage modes are needed for A-USC technology. Two Ni-based superalloys have been identified as prime candidates for valves based materials. Hardfacing is applied to sealing surfaces to protect them from wear and to reduce friction. Stellite 6 (Cobalt-based alloy) is the benchmark hardfacing owing to its anti-galling properties. However, the latest results tend to indicate that it is not suitable for high pressure application above 700°C. An alternative hardfacing will be required for A-USC. New Ni- and Co- based alloys are being developed for applications where extreme wear is combined with high temperatures and corrosive media. Their chemistry accounts for the excellent dry-running properties of these alloys and makes them very suitable for use in adhesive (metal-to- metal) wear. These new alloys have better wear, erosion, and corrosion resistance than Stellite 6 in the temperature range 800°C ~ 1000°C. As such, they have the potential to operate in A-USC. Velan recently developed an instrumented high temperature tribometer in collaboration with Polytechnique Montreal to characterize new alloys including static and dynamic coefficients of friction up to 800°C. We present herein the methodology that has been devolved to explore the effects of elevated temperature on the tribological behavior of those advanced material systems, with the goal of capturing the basis for the specification, design, fabrication, operation, and maintenance of valves for A-USC steam power plants.