Search Results for erosion resistance

This presentation compares the corrosion resistance of uncoated Haynes 230 and SS316HS substrates to the same substrates coated with a Fe-based amorphous alloy. The substrates were exposed to highly corrosive media, FLiNaK, for 120 hours at 700 °C. The findings indicate that the thermal spray amorphous alloy coating provided superior corrosion resistance within the coatings while protecting the substrates against the aggressive environment. As a result, the new amorphous metal coating improved the substrate's lifespan by providing better protection against high-temperature corrosion, paving the way for a more efficient and cost-effective future in various industrial applications.

Erosion from solid and liquid particles in gas turbine and steam turbine compressors degrades efficiency, increasing downtime and operating costs. Conventional erosion-resistant coatings have temperature and durability limitations. Under an Electric Power Research Institute (EPRI) project, ultra-hard nano-coatings (~40 microns thick) were developed using Plasma Enhanced Magnetron Sputtering (PEMS). In Phase I, various coatings—including TiSiCN nanocomposites, stellite variants, TiN monolayers, and multi-layered Ti-TiN and Ti-TiSiCN—were deposited on turbine alloys (Ti-6Al-4V, 17-4 PH, Custom-450, and Type 403 stainless steel) for screening. Unlike conventional deposition methods (APS, LPPS, CVD, PVD), PEMS employs high-current-density plasma and heavy ion bombardment for superior adhesion and microstructure density. A novel approach using trimethylsilane gas successfully produced TiSiCN nanocomposites. Stellite coatings showed no erosion improvement and were discontinued, but other hard coatings demonstrated exceptional erosion resistance—up to 25 times better than uncoated substrates and 20 times better than traditional nitride coatings. This paper details the deposition process, coating properties, adhesion tests, and characterization via SEM-EDS, XRD, nanoindentation, and sand erosion tests.

Competitive pressures throughout the power generation market are forcing individual power plants to extend time between scheduled outages, and absolutely avoid costly forced outages. Coal fired power plant owners expect their engineering and maintenance teams to identify, predict and solve potential outage causing equipment failures and use the newest advanced technologies to resolve and evade these situations. In coal fired power plants, erosion not only leads to eventual failure, but during the life cycle of a component, affects the performance and efficiency due to the loss of engineered geometry. “Wear” is used very generally to describe a component wearing out; however, there are numerous “modes of wear.” Abrasion, erosion, and corrosion are a few of the instigators of critical component wear, loss of geometry, and eventual failure in coal fired plants. Identification of the wear derivation is critical to selecting the proper material to avoid costly down-times and extend outage to outage goals. This paper will focus on the proper selection of erosion resistant materials in the severe environment of a coal fired power plant by qualifying lab results with actual field experiences.

Solid particle erosion (SPE) and liquid droplet erosion (LDE) cause severe damage to turbine components and lead to premature failures, business loss and rapier costs to power plant owners and operators. Under a program funded by the Electric Power Research Institute (EPRI), nano­coatings are under development for application in steam and gas turbines to mitigate the adverse effects of PE and LPE on rotating blades and stationary vanes. Based on a thorough study of the available information, most promising coatings such as nano-structured titanium silicon carbo-nitride (TiSiCN), titanium nitride (TiN) and multilayered nano coatings were selected. TurboMet International (TurboMet) teamed with Southwest Research Institute (SwRI) with state-of-the-art nano-technology coating facilities with plasma enhanced magnetron sputtering (PEMS) method to apply these coatings on various substrates. Ti-6V-4Al, 12Cr, 17-4PH, and Custom 450 stainless steel substrates were selected based on the current alloys used in gas turbine compressors and steam turbine blades and vanes. Coatings with up to 30 micron thickness have been deposited on small test coupons. These are extremely hard coatings with good adhesion strength and optimum toughness. Tests conducted on coated coupons by solid particle erosion (SPE) and liquid droplet erosion (LDE) testing indicate that these coatings have excellent erosion resistance. The erosion resistance under both SPE and LDE test conditions showed the nano-structured coatings have high erosion resistance compared to other commercially produced erosion resistance coatings. Tension and high-cycle fatigue test results revealed that the hard nano-coatings do not have any adverse effects on these properties but may provide positive contribution.

An international initiative is underway to develop the first standardized high-temperature solid particle erosion test method for steam turbine applications, addressing limitations of the current room-temperature ASTM G76 standard. Led by EPRI, this program involves laboratories from seven countries in a “Round Robin” testing program, aiming to establish consistent testing procedures for evaluating erosion resistance of materials used in Ultra Supercritical (USC) and advanced USC turbines. The proposed standard will use Type 410 stainless steel tested at 30 and 90-degree impingement angles with 50-micron alumina particles at 200 m/s, both at room temperature and 600°C, providing more relevant conditions for current and next-generation steam turbine applications.

Solid particle erosion (SPE) harms steam and gas turbines, reducing efficiency and raising costs. The push for ultra-supercritical turbines reignited interest in SPE’s impact on high-temperature alloys. While the gas turbine industry researches methods to improve erosion resistance, a similar need exists for steam turbines. Existing room-temperature SPE test standards are insufficient for evaluating turbine materials. To address this gap, an EPRI program is developing an elevated-temperature SPE standard. This collaborative effort, involving researchers from multiple countries, has yielded a draft standard submitted to ASTM for approval. This presentation will detail the program, test conditions, and the draft standard’s development.

Abradability, erosion and steam oxidation tests were conducted on commercial and experimental abradable coatings in order to evaluate their suitability for applications in steam turbines. Steam oxidation tests were carried out on free-standing top coat samples as well as coating systems consisting of a bond and an abradable top coat. Mapping of the abradability performance under widely varied seal strip incursion conditions was carried out for a candidate abradable coating that showed good steam oxidation performance in combination with good erosion resistance. The abradability tests were carried out on a specially designed test rig at elevated temperatures. The steam oxidation analysis combined with the abradability mapping results provide a potentially improved seal coating system that can be integrated into existing steam turbine designs for various seal locations. Such design integration is easily achieved and can be applied to steam turbine components that are sprayed in dedicated coating shops or even at the site of final turbine assembly.

As electricity markets become increasingly competitive, ultrasupercritical power plants must operate efficiently and flexibly. This necessitates attention to equipment design features and optimal material selection. Early studies by EPRI highlighted the need for boiler and steam turbine design improvements, as well as material advances, to enable the flexible operation of advanced supercritical units. Improvements such as turbine rotor cooling, cycling capability through improved control systems, enhanced blade tip sealing designs, turbine vibration control approaches, and erosion-resistant control stage designs were required. With ultrasupercritical plants moving towards even higher steam temperatures exceeding 700°C, these concerns need to be revisited from both metallurgical and design perspectives. Furthermore, features for efficiency improvements beyond advanced steam conditions should be considered, while minimizing environmental emissions like CO 2 . This paper reviews the needs for future ultrasupercritical plants with steam temperatures approaching or exceeding 700°C.

The INCONEL filler metals 72 and 72M have been utilized significantly for weld overlay protection of superheaters and reheaters, offering enhanced corrosion and erosion resistance in this service. Laboratory data conducted under simulated low-NOx combustion conditions, field exposure experience, and laboratory analysis (microstructure, chemical composition, overlay thickness measurements, micro-hardness) of field-exposed samples indicate that these overlay materials are also attractive options as protective overlays for water wall tubes in low-NOx boilers. Data and field observations will be compared for INCONEL filler metals 72, 72M, 625 and 622.

The measurement of damage from high temperature solid particle erosion (HTSPE) can be a lengthy process within the laboratory with many lab-based systems requiring sequential heat and cooling of the test piece to enable mass and/or scar volume measurements to be made ex situ. Over the last few years a new lab-based system has been in development at the National Physical Laboratory which has the ability to measure the mass and volume change of eroded samples in situ without the need to cool the sample. Results have previously been shown demonstrating the in situ mass measurement, more recently the in situ volume measurement capability has been added and used to evaluate the erosion performance of additively manufactured materials. Selective laser melting (SLM) is an advanced manufacturing method which is growing in popularity and application. It offers the ability to manufacture low volume complex parts and has been used in rapid prototyping. As the technique has developed there is increasing interest to take advantage of the ability to manufacture complex parts in one piece, which in some case can be more cost and time effective than traditional manufacturing routes. For all the benefits of SLM there are some constraints on the process, these include porosity and defects in the materials such as ‘kissing bonds’, surface roughness, trapped powder and microstructural variation. These features of the processing route may have implications for component performance such as strength, fatigue resistance wear and erosion. To investigate this further SLM IN718 has been used to evaluate factors such as surface roughness, microstructure and morphology on the erosion performance as measured in situ and compared with conventional produced wrought IN718 material.

Inconel Filler Metal 72 (FM 72) and Incoclad 671/800H co-extruded tubing have been successfully used for over 20 years to protect boiler tubing from high-temperature degradation. A newer alloy, FM 72M, offers superior weldability and the lowest corrosion rate in simulated low NOx environments. Both FM 72 and 72M show promise in addressing challenges like circumferential cracking and corrosion fatigue in waterwall tubing overlays. Additionally, 72M’s superior wear resistance makes it ideal for replacing erosion shields in superheater and reheater tubing. Beyond improved protection, these alloys exhibit increased hardness and thermal conductivity over time, leading to reduced temperature difference across the tube wall and consequently, enhanced boiler efficiency and lower maintenance costs. This paper discusses the historical selection of optimal alloys for waterwall and upper boiler tubing overlays, analyzes past failure mechanisms, and highlights the key properties of successful choices like FM 72 and 72M.

Work has been progressing over recent years to develop a standard test method for high temperature solid particle erosion testing. Early in 2015 this standard was published by ASTM as G211-14 Standard Test Method for Conducting Elevated Temperature Erosion Tests by Solid Particle Impingement Using Gas Jets. To support the development of this standard the European funded METROSION project has been conducting a comparison of different apparatus which employ different nozzle geometries, acceleration lengths, stand-off distances and heating and accelerating processes. The aim is to understand the influence these instrumental and experimental parameters have on the measured erosion rate and erosion mechanism. As part of this work three very distinct approaches have been compared using a common erodent and test pieces. Measurements have been performed at 600 °C with particle velocities of 50 to 320 m/s, using different stand-off distances, acceleration lengths and nozzle diameters for impact angles of 30 and 90°. This is the first time a comprehensive comparison of these parameters has been conducted and shows the relative influence of these experimental variables.

High-temperature solid particle erosion (SPE) is a major threat to efficiency in power plants and jet engines, potentially reducing turbine efficiency by 7-10% and causing significant CO 2 emissions. The sources of these particles vary widely, from volcanic ash in engines to fly ash in boilers and scale in turbines. While better surface engineering and coatings offer solutions, their development is hampered by a lack of standardized test methods and reliable models. To address this, the METROSION initiative aims to establish a comprehensive framework for characterizing the high-temperature SPE performance of new materials and coatings. This framework will require a step change in test methods and control, focusing on accurately measuring key parameters like temperature, flow rate, particle properties, and impact angles. This paper outlines the initiative’s goals, with a particular focus on the techniques used for in-situ measurements of temperature, particle velocity, and 3D shape/size.

Materials are the key to develop advanced ultra-supercritical (A-USC) steam generators. Operating at temperature up to 760°C and sustained pressure up to 4500 psi. Pressure vessel and piping materials may fail due to creep, oxidation, and erosion. Valves are particularly subjected to loss of function and leakage due to impermeant of the sealing surfaces. New materials, less susceptible to the above damage modes are needed for A-USC technology. Two Ni-based superalloys have been identified as prime candidates for valves based materials. Hardfacing is applied to sealing surfaces to protect them from wear and to reduce friction. Stellite 6 (Cobalt-based alloy) is the benchmark hardfacing owing to its anti-galling properties. However, the latest results tend to indicate that it is not suitable for high pressure application above 700°C. An alternative hardfacing will be required for A-USC. New Ni- and Co- based alloys are being developed for applications where extreme wear is combined with high temperatures and corrosive media. Their chemistry accounts for the excellent dry-running properties of these alloys and makes them very suitable for use in adhesive (metal-to- metal) wear. These new alloys have better wear, erosion, and corrosion resistance than Stellite 6 in the temperature range 800°C ~ 1000°C. As such, they have the potential to operate in A-USC. Velan recently developed an instrumented high temperature tribometer in collaboration with Polytechnique Montreal to characterize new alloys including static and dynamic coefficients of friction up to 800°C. We present herein the methodology that has been devolved to explore the effects of elevated temperature on the tribological behavior of those advanced material systems, with the goal of capturing the basis for the specification, design, fabrication, operation, and maintenance of valves for A-USC steam power plants.

Recently, boiler waterwall tube damage such as fireside corrosion and circumferential cracking in low NOx environments has become a serious issue in Japan, despite the typical use of relatively lower sulfur content coal is typically being used than in US. Thermal spray coating has been the most popular method for tube protection in Japan, and thermal spray coated tubes have been used for this purpose. However, extensive damage to thermal spray coating tubes from cracking and exfoliation has been recently experienced. It has been reported that the thermal fluctuations occurring due to operational changes create alternating stress, leading to cracking and exfoliation of the thermal sprayed thin coating. Corrosion-resistant weld overlays, such as Type 309 stainless steel (in sub-critical boilers) and Alloy 622 (in sub-critical and super-critical boilers), are commonly used to protect boiler tubes from corrosion in low NOx coal fired boilers in U.S. In order to develop a fundamental understanding of the high temperature corrosive behavior of Alloy 622 weld overlay, gaseous corrosion testing and certain mechanical tests for consideration of long-term aging were undertaken. After four years of service in the low NOx combustion environment of a coal fired supercritical boiler, field tests on Alloy 622 weld overlay panels are in continuation. This paper describes the field test behavior of Alloy 622 weld overlay panels installed in a Japanese supercritical boiler, the laboratory results of weight loss corrosion testing, and the results of cyclic bend tests with overlay welded tubes related to aging.

This study explores the expanded applications of Alloy J513, a high-performance material traditionally used in cast engine valvetrain components, for powder metallurgy and surface cladding applications. While already recognized for its superior heat and wear resistance at a lower cost compared to cobalt-based hardfacing materials, J513 demonstrates additional advantages in powder metallurgy applications due to its ability to achieve desired powder characteristics through atomization without requiring post-atomization annealing. Through experimental investigation based on fundamental metallurgical principles and cladding engineering processes, the presented research demonstrates J513’s exceptional weldability and favorable weldment structure compared to conventional cobalt-based alloys. The study establishes crucial relationships between weldment behavior and unit energy input, providing valuable insights for advanced cladding techniques while highlighting J513’s potential as a sustainable alternative to traditional nickel- and cobalt-based alloys in various manufacturing processes, including surface overlay and additive manufacturing.

Steam turbine is one of the critical equipments in coal-fired power plants, steel P91 is a common material of its control valves. CoCr-based hardfacing on valve seats can resist long time exposure to water vapor with high temperature, thermal fatigue and solid particles erosion under high pressure. However, these hardfacing can crack and disbond during operation, which generates high risks for turbine systems and power plants. This article discussed the failure reasons of CoCr-based hardfacing, and introduced a method and practical experience of on-site repairing steam turbine valve seats with laser cladding NiCr coating.

The long-term performance of superheater super 304h tube during the normal service of an ultra-supercritical 1000mw thermal power unit was tracked and analyzed, and the metallographic structure and performance of the original tube sample and tubes after 23,400h, 56,000h, 64,000 h, 70,000 h and 80,000 h service were tested. The results show that the tensile strength, yield strength and post-break elongation meet the requirements of ASME SA213 S30432 after long-term service, but the impact toughness decreases significantly. The metallographic organization is composed of the original complete austenite structure and gradually changes to the austenite + twin + second phase precipitates. With the extension of time, the number of second phases of coarseness in the crystal and the crystal boundary increases, and the degree of chain distribution increases. The precipitation phase on the grain boundary is dominated by M 23 C 6 , and there are several mx phases dominated by NbC and densely distributed copper phases in the crystal. The service environment produces a high magnetic equivalent and magnetic induction of the material, the reason is that there are strips of martensite on both sides of the grain boundary, and the number of martensite increases with the length of service.

For four decades, the Electric Power Research Institute (EPRI) has led groundbreaking materials research in the power industry, yielding significant cost savings across fossil, nuclear, and power delivery sectors. This paper outlines EPRI's fossil-related research, conducted through three major programs: Fossil Materials&Repair (P87 Base program), Materials-Fossil&Nuclear strategic program, and a supplemental program addressing key industry initiatives. EPRI's research focuses on understanding damage mechanisms, developing improved materials, enhancing life prediction methodologies, and advancing component degradation assessment. The paper highlights the synergy between EPRI's short- and long-term research initiatives, referencing several presentations from the 6th International Conference on Advances in Materials Technology for Fossil Power Plants. By showcasing EPRI's comprehensive approach to materials research, this overview demonstrates the institute's ongoing commitment to advancing power generation technology and efficiency.

High efficiency in power generation is not only desirable because of economical reasons but also for enhanced environmental performance meaning reduced quantity of forming ash and emissions. In modern medium to large size plants, improvements require supercritical steam values. Furthermore, in future there will be an increasing share of renewables, such as wind and solar power, which will enhance the fluctuation of supply with the consequence that other power sources will have to compensate by operating in a more demanding cyclic or ramping mode. The next generation plant will need to operate at higher temperatures and pressure cycles coupled with demanding hot corrosion and oxidation environments. Such an operation will significantly influence the performance of materials used for boilers and heat exchanger components by accelerating oxidation rates and lowering mechanical properties like creep resistance. The paper discusses the oxidation behaviour of San25, 800H and alloy 263 in supercritical water at temperatures 650 and 700 °C at 250 bar, and compares the changes of mechanical properties of materials at these temperatures.