1-16 of 16 Search Results for

transmission lines

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Alloy Digest (1968) 17 (7): Cu-189.
Published: 01 July 1968
... Hitenso-1622 is a copper-cadmium alloy characterized by high strength, abrasion resistance and relatively high electrical conductivity. (Formerly known as Hitenso BB-961). It is recommended for electrical equipment, trolley wire, low temperature transmission lines and relays. This datasheet...
Journal Articles
Alloy Digest (2012) 61 (4): Cu-805.
Published: 01 April 2012
..., and spring quality. Products Available: The standard forms available are rod, bar, wire, and flatwire. For other forms, please contact the producer. Applications: Because of its good strength and wear resistance, ACB Hitenso C16200 was used for low-load transmission lines in rural areas for its earliest...
Journal Articles
Alloy Digest (2018) 67 (9): SS-1294.
Published: 01 September 2018
... transmission lines, abrasion- and corrosion-resistant screens, high strength non-magnetic springs, wire forms, racks, and cages. Producer Electralloy, a Division G.O Carson, Inc. Oil City, PA 16301, USA Tel: +1-814-678-4100 Fax: +1-814-678-4172 www.electralloy.com ISSN: 002-614X SS-1294B ...
Journal Articles
Alloy Digest (1988) 37 (10): Cu-541.
Published: 01 October 1988
... and electric blanket elements. spring contacts. high-strength transmission lines, connectors, cable wrap, switch-gear components. wave guide cavities. Manufacturer: Copper and coppea alloy producing mills. ...
Journal Articles
Alloy Digest (1973) 22 (3): SA-286.
Published: 01 March 1973
... Test) on straight seam-welded 30.inch diameter, 3/8-inch wall thickness, gas-transmission line pipe was made in the presence of a through-wall flaw approximately 4 inches in length. A pressure of over 2000 psi was required to cause rupture at a test temperature of -650F. At this temperature...
Journal Articles
Alloy Digest (1976) 25 (7): Cu-315.
Published: 01 July 1976
... electrodes, current-carrying rings, switch-gear components, waveguide cavities, spring contacts, back-up bars, railbands, connectors and high- strength transmission lines. Manufacturer: Ampco Metal Division of Ampco-Pittsburgh Corporation Milwaukee, Wisconsin 53201. ...
Journal Articles
Alloy Digest (1968) 17 (2): CI-35.
Published: 01 February 1968
... pulleys for diesel engines, insulator caps for high-tension electric transmission lines, power shovels, farm implements. Manufacturer: Link-Belt Ewart Foundry Indianapolis, lndiana ...
Journal Articles
Alloy Digest (1992) 41 (4): P-34.
Published: 01 April 1992
... - o.ooo2 Seconds 60-135 Table 3 -TYPICAL ROOM-TEMPERATURE GAS PERME- ABILITY AND WATER VAPOR TRANSMISSION DATA (VARIOUS TYPES OF MOLDED POLYSTYRENE) Gas Permeability, Water Vapor Transmission, cc/mi1/100 in2JatmJday gm/mil/100in2/day (75100┬░F) 02 N2 co2 300-400 40-50 looo-1500 2-10 - Corrosion Resistance...
Journal Articles
Alloy Digest (2005) 54 (11): SA-552.
Published: 01 November 2005
... for Hollow Bar using Sandvik Coromant P-Line Inserts Rough turning Cutting tool, CNMG 120412-PM, GC4025; wearout time, 15 min; wear out criterion Vbmax, 0.40 mm; nose radius, 1.2 mm; holder, PCLNL 2525 M12; cutting fluid, Oemeta S33 V24 5%(a) Cutting speed, Cutting depth, mm Feed, mm/rev m/min Power, kW 1...
Journal Articles
Alloy Digest (1975) 24 (11): SS-320.
Published: 01 November 1975
... and skid wire for under- ground pipe-type electrical transmission systems, and pole-line hardware. Manufacturer: Advanced Materials Division Armco Steel Corporation Baltimore, Maryland 2 1203. ...
Journal Articles
Alloy Digest (1958) 7 (2): Al-63.
Published: 01 February 1958
...- ance, and good wehdabiliy. Formerly known as AIuminum 66s and Harvey 66-S. Forms Available: Extrusions, tube, rod, bar, forgings and impact ex- trusions. Applications: General structures, gas engine and water heater tubes, water line and condenser tubes, scafTolds, rails, booms. mullions...
Journal Articles
Alloy Digest (1973) 22 (7): Pb-10.
Published: 01 July 1973
.... Forms Available: Precision inserts of babbit-lined strip, lined bearing shells, ingots, bars and die castings. Applications: Alloy 7: Used for moderate loads and speeds in blowers, pumps, electric motors and machine tools. Alloy 8: Light loads and moderate speeds in mining machinery, transmission...
Journal Articles
Alloy Digest (1985) 34 (8): Al-259.
Published: 01 August 1985
... machinability. High-speed-steel cutting tools are satisfactory but hard grades of carbide are preferred. Single-point tools should have 20-50 deg. top rake, IO-20 deg. side rake, 8-10 deg. front and side clearance angles, operating at high speeds and line to medium feeds. Cutting edges of tools must be keen...
Journal Articles
Alloy Digest (1998) 47 (8): Al-351.
Published: 01 August 1998
... for applications requiring tight dimensional control after ma- chining. The T9 temper has been used heavily in automotive transmission valve, brake piston. and air conditioning compres- sor piston applications. Camera parts, couplings, marine fittings, hinge pins, knobs, mag- neto parts, nuts, oil line fittings...
Journal Articles
Alloy Digest (1952) 1 (2): Al-2.
Published: 01 October 1952
... of subsequent warping or distortion. By use of this alloy, d& 3ty,1-l .=u=d b -Pa and gh tempentrrrr sud Forms Available: Sand castings aud ingots. Applications: High strength and pressure tight castings, manifolds, transmission housings, aircraft componenp, radio equipment, bushings, oxyE= control units, od...
Journal Articles
Alloy Digest (1970) 19 (3): CS-33.
Published: 01 March 1970
... strength. Stretcher-strain markings may occur in annealed material on deep drawmg and some orange-peel appearance as urrth large gramed marenal. Stretcher-strain lines are due to the double vield ooint. Hot roied &up and sheet are produced tn three pnncipal aualities. namely. commercial oualitv. drawmg...