Search Results for microstructure

1064, 1065, CS65, S65CM, S65C, and S65C-CSP are wrought high-carbon non-alloy steels that are typically used in the cold reduced, patented and cold drawn, quenched and tempered, or austempered condition. These steels are widely used for highly stressed parts that require higher strength levels than can be achieved with lower carbon grades. They are also used for applications where the higher carbon is needed to improve wear characteristics. This datasheet provides information on composition, physical properties, microstructure, hardness, and tensile properties. It also includes information on high temperature performance as well as forming and heat treating. Filing Code: CS-270. Producer or source: Heat Treater’s Guide Data Sheet.

8620, 8620H, 8620RH, 20NiCrMo2-2, 20NiCrMoS2-2, SNCM220, and SNCM220H are wrought, low-carbon, nickel-chromium-molybdenum, low alloy steels that are typically used in the carburized or carbonitrided, and subsequently quench hardened, and tempered condition. In general, these steels are intended for the manufacture of small- and medium-sized case-hardened parts that require a high hardness, high carbon, martensitic case with good wear and fatigue resistance, and a strong and tough low-carbon steel core. This datasheet provides information on composition, physical properties, microstructure, hardness, and tensile properties. It also includes information on high temperature performance as well as forming and heat treating. Filing Code: SA-879. Producer or source: Heat Treater’s Guide Data Sheet.

1006 is a wrought low-carbon (carbon ≤ 0.08%) non-alloy steel that is used in the as rolled, annealed, normalized, or cold worked condition. This steel is characterized by low strength, high ductility, excellent cold formability, and excellent weldability. Within the carbon range of this steel grade, both strength and hardness will increase with increase in carbon and with cold work. Such increases in strength are at the sacrifice of ductility or the ability to withstand cold deformation. 1006 is widely used for lightly stressed parts where cold formability or drawability is the primary requisite. In general, it is not intended for heat treatment after cold working. 1006 may, however, be used in the case hardened, nitrided, or nitrocarburized condition. This datasheet provides information on composition, physical properties, microstructure, hardness, and tensile properties. It also includes information on forming and heat treating. Filing Code: CS-267. Producer or source: Heat Treater's Guide.

1012 and S12C are wrought low-carbon (carbon = 0.10–0.15 percent) non-alloy steels that are used in the as rolled, annealed, normalized, or cold worked condition. These steels are characterized by low strength, high ductility, excellent cold formability, and excellent weldability. Within the carbon range of these steel grades, strength and hardness will increase with increase in carbon content and with cold work. Such increases in strength are at the sacrifice of ductility or the ability to withstand cold deformation. Grades 1012 and S12C are widely used for lightly stressed parts that require higher strength levels than can be achieved by the lower carbon grades and for applications where cold formability is the primary requisite. They are less expensive than 1008 and can be used when the requirements for cold forming are less exacting. 1012 and S12C may also be used in the case hardened, nitrided, or nitrocarburized condition. This datasheet provides information on composition, physical properties, microstructure, hardness, and tensile properties. It also includes information on low and high temperature performance as well as forming and heat treating. Filing Code: CS-268. Producer or source: Heat Treater's Guide.

1016, C16E, and C16R are wrought low-carbon (carbon = 0.12–0.18%) non-alloy steels that are used in the as-rolled, annealed, normalized, or cold worked condition. They are widely used for lightly and moderately stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and also for applications where a combination of low-to-medium strength, excellent cold formability, and excellent weldability are required. These steels may also be used in the case hardened, nitrided, or nitrocarburized condition. This datasheet provides information on composition, physical properties, microstructure, hardness, and tensile properties. It also includes information on low and high temperature performance as well as forming and heat treating. Filing Code: CS-269. Producer or source: Heat Treater's Guide Data Sheet.

1015, C15E, and C15R are wrought low-carbon (carbon equals 0.12 to 0.18 percent) non-alloy steels that are used in the as rolled, annealed, normalized, or cold worked condition. They are widely used for lightly and moderately stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and also for applications where a combination of low-to-medium strength, excellent cold formability, and excellent weldability are required. These steels may also be used in the case hardened, nitrided, or nitrocarburized condition. This datasheet provides information on composition, physical properties, microstructure, hardness, and tensile properties. It also includes information on forming and heat treating. Filing Code: CS-266. Producer or source: Heat Treater’s Guide.

Alcoa EZCast-NHT A152 and A153 are proprietary, non-heat-treatable, high-pressure die casting (HPDC) aluminum alloys in which magnesium is the principal alloying element. These alloys develop the required strength and toughness in the as-cast condition, thus eliminating or minimizing numerous production problems, such as distortion, blistering, property variations, and heat treatment logistics. This datasheet provides information on composition, physical properties, microstructure, elasticity, and tensile properties. It also includes information on corrosion resistance. Filing Code: Al-469. Producer or source: Alcoa Corporation.

Ductile Iron grade 45-12 produced by continuous casting has consistent density and fine grain structure. It is the softest of the regular grades of ductile iron and it machines at high speeds with good surface finish. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, and tensile properties. It also includes information on heat treating, machining, and joining. Filing Code: CI-58. Producer or source: Federal Bronze Products Inc..

MITTAL DI-FORM T700 and HF80Y100T are low-carbon steels with a manganese and silicon composition. Dual-phase (DP) steels are one of the important advanced high-strength steel (AHSS) products developed for the automotive industry. Their microstructure typically consists of a soft ferrite phase with dispersed islands of a hard martensite phase. The martensite phase is substantially stronger than the ferrite phase. The DI-FORM grades exhibit low yield-to-tensile strengths, and the numeric designation in the name corresponds to the tensile strength. This datasheet provides information on microstructure and tensile properties as well as deformation and fatigue. It also includes information on forming. Filing Code: SA-561. Producer or source: Mittal Steel USA Flat Products.

55-06 and 70-02 Ductile Dura-Bar are continuously cast ductile irons with about 50 and 75% pearlitic microstructures, respectively. 55-06 has about the same tensile strength as SAE 1045 as-hot-rolled steel. Its maximum yield strength and elongation are equivalent to a eutectoid carbon steel. 70-02 Ductile Dura-Bar has somewhat greater tensile strength up to 3 diameter and considerably higher yield strength up through 10 diameter. The elongation of 70-02 is lower than that of 55-06 because of its reduced ferrite content. This datasheet provides information on composition, microstructure, and hardness. It also includes information on heat treating. Filing Code: CI-62. Producer or source: Federal Bronze Products Inc..

Dura-Bar 202 (Type 2) Ni-Resist Iron is a flake graphite austentic cast iron that is produced by the continuous casting process. It is suitable for most applications requiring Dura-Bar 201 (Type 1) Ni-Resist Iron, and the grades are often used interchangeably. The machinability of Dura-Bar 202 (Type 2) Ni-Resist Iron will be similar to the pearlitic grades of gray iron, namely G2 and G2A. It is especially suitable for service temperatures above 705°C (1300°F) and in the stem handleing applications. Copper levels are maximized at 0.50%, and this grade is suitable for food grade applications. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as heat treating. Filing Code: CI-100. Producer or source: Dura-Bar Metal Services.

MITTAL DI-FORM T590 and T600 are low-carbon dual-phase steels containing manganese and silicon. Dual-phase (DP) steels are important advanced high-strength steel (AHSS) products developed for the automotive industry. Their microstructure typically consists of a soft ferrite phase with dispersed islands of a hard martensite phase. The martensite phase is substantially stronger than the ferrite phase. The DI-FORM grades exhibit low yield-to-tensile strength ratios. The numeric designation in the grade name corresponds to the tensile strength in MPa. This datasheet provides information on microstructure, tensile properties, and bend strength as well as fatigue. It also includes information on forming. Filing Code: SA-558. Producer or source: Mittal Steel USA Flat Products.

MITTAL DI-FORM 140T and HB T965 are low carbon steels with dual phase manganese and silicon composition. Dual-phase (DP) steel microstructures typically consist of a soft ferrite phase with dispersed islands of a hard martensite phase. The martensite phase is substantially stronger than the ferrite phase. The dual-phase grades, including those with high tensile strengths of 965 MPa (140 ksi), that are designed for forming (DI-FORM), also have low yield-strength-to-tensile-strength ratios to improve formability. This datasheet provides information on microstructure and tensile properties as well as deformation and fatigue. It also includes information on forming and surface treatment. Filing Code: SA-566. Producer or source: Mittal Steel USA Flat Products.

DURA-BAR G1A alloyed iron is engineered for the glass mold industry. It is produced by continuous casting which results in fine graphite flake size and size and fine matrix structure. This datasheet provides information on composition, microstructure, and hardness. It also includes information on heat treating and machining. Filing Code: CI-61. Producer or source: Federal Bronze Products Inc..

Tribaloy T-401 is a cobalt hardfacing alloy with smaller Laves phase particles to promote ductility and keep corrosion resistance and wear properties. This datasheet provides information on composition, microstructure, and hardness. It also includes information on high temperature performance and corrosion resistance as well as casting, forming, joining, and powder metal forms. Filing Code: CO-113. Producer or source: Deloro Stellite Company Inc.

Questek QT-Ti-1A, 2A, and 2B are three developed castable titanium alloys under U.S. Army-funded SBIR Phase I and II programs to incorporate lower-cost raw materials and exhibit greater strength and/or ductility than Ti-6-4. This datasheet provides information on microstructure and tensile properties. It also includes information on high temperature performance as well as casting. Filing Code: Ti-155. Producer or source: QuesTek Innovations, LLC.

Arcam ASTM F75 CoCr is a cobalt-based, solid-solution-strengthened alloy that is used for the production of additively manufactured components using electron beam melting (EBM). These components are used in demanding applications in the aerospace, biomedical, and high-performance engineering sectors. This datasheet provides information on composition, physical properties, microstructure, hardness, and tensile properties as well as fatigue. It also includes information on corrosion resistance as well as heat treating and machining. Filing Code: Co-132. Producer or source: Arcam AB (a GE Additive company).

ZGS Platinum is a grain stabilized platinum containing a small amount of highly dispersed zirconium oxide. Its properties combine to provide greater high-temperature strength and, in some applications, greater contamination resistance than that of pure platinum. Applications include laboratory crucibles and dishes. An exacting application is in the production of fibre glass which invloved the rapid flow of molten glass at temperatures of 1250-1350 C through a pierced plate which must retain its shape and alignment. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, and tensile properties as well as creep. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Pt-2. Producer or source: Matthey Bishop Inc..

Dura-Bar 65-45-12X is a ductile iron that is used for the production of continuous cast products. Its microstructure consists of nodular graphite and a matrix comprising ferrite and 10–50% pearlite. The predominantly ferritic matrix of Dura-Bar 65-45-12X allows it to be easily machined as opposed to steels and pearlitic irons. Dura-Bar 65-45-12X is a suitable alternative to low and medium carbon non-alloy steels. It is appropriate for applications necessitating fatigue strength and ductility. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, and tensile properties. It also includes information on heat treating and machining. Filing Code: CI-88. Producer or source: Charter Dura-Bar, Inc.

Superplast is a plastic mold steel with a high chromium content for corrosion resistance and a high sulfur content for good machinability. This datasheet provides information on composition, microstructure, hardness, and tensile properties. It also includes information on corrosion resistance as well as forming, machining, and joining. Filing Code: SS-1261. Producer or source: International Mold Steel Inc..