Skip Nav Destination
Search Results for knife applications
1-20 of 32 Search Results for
Alloy Digest (2006) 55 (2): SS-954.
Published: 01 February 2006
... Sandvik 12C27 is a martensitic stainless steel for knife applications. It is supplied in both the annealed or cold-rolled condition. This datasheet provides information on composition, microstructure, hardness, and tensile properties. It also includes information on forming and heat treating...
Alloy Digest (2014) 63 (9): SS-1182.
Published: 01 September 2014
... Carpenter CTS-BD30P is a high-performance blade steel that forms numerous carbides with a fine distribution. A tempered hardness capability of HRC 58/60 combined with superior edger retention make this alloy a candidate for cutlery applications in multiple cutlery and knife market segments...
Alloy Digest (1977) 26 (9): Ni-249.
Published: 01 September 1977
... HASTELLOY alloy B-2 has outstanding corrosion resistance in the as-welded condition. It is an improved wrought version of HASTELLOY alloy B with the same excellent corrosion resistance as alloy B, but with improved resistance to knife line and heat-affected zone attack. Alloy B-2 resists...
Alloy Digest (1981) 30 (7): SS-389.
Published: 01 July 1981
... the austenitic and marten&c stainless steels; that is, it has some of the properties of each. Its uses include high-strength structural applications, corrosion-resistant springs and knife blades. Composition: Carbon Manganese Silicon ChIOlIliUIll Nickel Molybdenum Nitrogen Iron Typical 0.10 0.75 0.30 16.50 4.25...
Alloy Digest (1980) 29 (2): SS-371.
Published: 01 February 1980
... Stainless Steel Or FEBRUARY 1980 BIGIST - DATA ON WORLD WIDE METALS AND ALLOYS 0 Copyright 1980, Enpinesrinp Publications, Inc. Afl rights reserved. Pubhhed by ~g&v~F&t h- Upper Mantdak. New Jersey UHB* Stainless AEB-L (Hardenable Stainless Knife Steel) UHB Stainless AEB-L is a hardenable (martensitic...
Alloy Digest (2008) 57 (9): SS-1017.
Published: 01 September 2008
... the achievement of a sharp cutting edge. Combined with its good corrosion resistance, this aptitude meets the requirements of numerous blade applications. For kitchen knife blades and those used in the food preparation utensils, the molybdenum-containing Uginox MA3M and MA5MV grades are to be preferred, due...
Alloy Digest (2009) 58 (3): SS-1031.
Published: 01 March 2009
.... Thus, in the quenched and tempered condition, it attains high strength levels enabling the achievement of a sharp cutting edge. Combined with its good corrosion resistance, this aptitude meets the requirements of numerous blade applications. For kitchen knife blades and those used in food preparation...
Alloy Digest (1997) 46 (5): TS-555.
Published: 01 May 1997
....ckrgeintofurnace6oooForbelow. 2. Heatevenlyat~~ly2ooQF/hto17oooEDo~rfoorce~ hearing. 1Mnofleast conmilm- Quemhing. Quench in agitated oil from 1700°F. When tempera- ture of knife has dropped to approximately 6OO F, remove Itom oilbathandimmedi&yplaceinmmperingfurnaceat400°F. Tempering. After knife has equal&d itself at 400°F...
Alloy Digest (2013) 62 (8): SS-1154.
Published: 01 August 2013
... that forms numerous carbides with a fine distribution. A tempered hardness capability of HRC 58/60 combined with superior edge retention make this alloy an excellent candidate for cutlery applications in multiple cutlery and knife market segments. Carbon 1.50 Phosphorus 0.040 max Sulfur 0.030 max Manganese...
Alloy Digest (1997) 46 (1): SS-669.
Published: 01 January 1997
... Applications: Producer: Cutlery, kitchen knives, pocket knife blades. meat knives, vemia callipm. surgical instruments, brake discs, and die sheets. Tbyssen StabI AG Krefeld. Germany (02151) 83-01 ISSN: 002-614X In USA: Thyssen specialty steels. Inc. carol strtam. IL 60188 (708) 682-3900 SS-669B ...
Alloy Digest (2006) 55 (12): CS-147.
Published: 01 December 2006
.... The dimensions of the fatigue samples are available from the manufacturer. Fig. 3 Blanking performance. Limits of theoretical shearing force. Calculated from 2003 plant data, knife angle 0.5° Fig. 4 Formability. Forming limit curve for 2.0 mm Tenform Fig. 5 Springback. Comparison of theoretical springback...
Alloy Digest (2007) 56 (1): CS-148.
Published: 01 January 2007
... shearing force calculated from 2004 plant data (knife angle 0.5°) Fig. 5 Formability. Forming limit curve for 2.9 mm Tenform XF450 Fig. 6 Springback. Comparison of theoretical springback for a bending angle of 90° Applications: Applications include automotive chassis and underbody components, warehouse...
Alloy Digest (1974) 23 (3): CI-42.
Published: 01 March 1974
... abrasion resistant applications involving scratching with slight impact. as encountered in end liners, wear shoes, sand-pump impellers and similar parts. Almanite W is conveniently separated into types Wl, W2 and W4. All of these are white irons with excess carbon in the form of hard wearing carbides. Type...
Alloy Digest (2001) 50 (10): SS-832.
Published: 01 October 2001
... applications include knife blades, bearings, valve com- ponents, and bushings. Producer: Timken Latrobe Steel A Timken Company Subsidiary Latrobe, PA (724) 537-7711 (724) 532-6316 (fax) ISSN: 002-614X SS-832B Fig. 1 Hardness versus tempering temperature for different austenitizing temperatures and quench media...
Alloy Digest (1986) 35 (2): SS-467.
Published: 01 February 1986
... products Applications: Springs. heat-rrearcd iasteners. knife blades. mtsccllancous lorgtngs. Manufacturer: -\lle_ehcn! Ludlum Steel Corporation Pittsburgh. Pennsylvania 15222. ...
Alloy Digest (2009) 58 (11): Ni-675.
Published: 01 November 2009
.... Applications: Because of its high strength and excellent toughness at high temperature, this alloy is an excellent choice for hot work tooling and dies, including hot shear knife blades. Good corrosion resistance and strength contribute to its choice for use in oil and gas extraction. It is also a preferred...
Alloy Digest (1967) 16 (12): TS-200.
Published: 01 December 1967
... Available: Billers, forgings, bars Applications: Gauges, knife edges, knurls, caps, dies, arbors, rolls, bearings. Manufacturer: Universal-Cyclops Specialry Steel Division Cyclops Corporarion Pittsburgh, Pennsylvania ...
Alloy Digest (2019) 68 (5): SS-1306.
Published: 01 May 2019
... the highest hardness of any stainless steel (about HRC 61.5). This material is not usually recommended for elevated temperature applications. Product Forms Available Bar rounds, strip, wire, rod Applications This material has found application in specialty knife blade applications. Its fine carbide...
Alloy Digest (1988) 37 (11): Zn-44.
Published: 01 November 1988
... to dissipate the hot-spot effect of ingates by adopting a thin, wide, knife or kiss gate, ormultiplegates,ratherthanasingleheavyingate. Theuse of chills, possibly combined with insulated top risers, is helpful in reducing bottom shrinks in heavy sections. Casting temperatures should be kept as low as possible...
Alloy Digest (1963) 12 (6): SS-29.
Published: 01 June 1963
... with carbide-ripped tools when applicable. Single point turning tools of high speed steel may be ground 5-10 deg. back rake, 5-8 deg. srde clearance, 7-10 deg. front clearance, 8-15 deg. cutting-edge angle and lo-15 deg lead angle. Use a sulphur-chlorinated cutting fluid. Workability: Good forming properties...