1-20 of 30 Search Results for

drill jigs

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Alloy Digest (1978) 27 (8): Bi-6.
Published: 01 August 1978
... CERROBEND Alloy is a bismuth-base eutectic alloy that melts at 158 F (70 C). It is low melting temperature and controlled-shrinkage characteristics make it highly useful industry for such applications as anchoring bushings in drill jigs, cores for spinning and tube-bending filler. This datasheet...
Journal Articles
Alloy Digest (2005) 54 (4): Cu-733.
Published: 01 April 2005
... involving compressive wear and high abrasion, especially where no impact is present. Uses include die rings, forming rolls, inserts, wiping blocks, cam followers, pilot bushings, dies, and drill jig bushings. The alloy is also used in plastic mold applica- tions such as ejector sleeves and bushings, guide...
Journal Articles
Alloy Digest (1961) 10 (11): Cu-110.
Published: 01 November 1961
.... It has a medium hardness. This alloy can be used for bearings for light loads and soft mating members. It can be cold worked slightly and has about the best machinability of this series of iron-aluminum-copper alloys. Forms Available: Forgings, rods, screw machine products. Applications: Drill jigs, cams...
Journal Articles
Alloy Digest (1970) 19 (3): Cu-212.
Published: 01 March 1970
... of ironaluminuxntopper alloys. F- Availablez Forgings, rods, screw machine products. Applicltionr. Drill jigs, cams, coliets, rollers, gibs, gears, pole line hardware, fasteners. bearings, bushings, housings, valve stems. Mfmdacmrar: Mueller Brass Company Port Haron, Michigan ...
Journal Articles
Alloy Digest (1960) 9 (9): Cu-92.
Published: 01 September 1960
... and sea water. Applications: Drill jigs, cams, collets, rollers, gibs, boring bar guides, gears, pole-line hardware, fasteners, bear- ings, housings, valve seat inserts, propeller hub cones. Tuf-Stuf 224C is an aluminum bronze having a low coefficient of friction, good wearing qualities, high tensile...
Journal Articles
Alloy Digest (1978) 27 (10): Cu-361.
Published: 01 October 1978
... to 314 in DriUs should have 12-20 deg. lip clearance and 100-l 10 deg. included point angle. Aircraft landing gear bushings, pickling equipment, valve parts, pump parts, nuts, aircraft engine parts, gears, worm% shafts, va.lve seat inserts, spark plug bushings, propeller hub cones, drill, jigs, molds...
Journal Articles
Alloy Digest (1954) 3 (4): Cu-15.
Published: 01 April 1954
..., propeller hub cones, drill jigs, molds, rollers, lead screw nuts and clutch shifter forks. Manufacturer: Mueller Brass Company Port Huron, Michigan 1Or DIGEST CARPENTER No. 5-876 Rltgc kfA-8 -w DECRMEER 19E2 DATA ON WORLD WIDE METALS AND ALLOYS Publisbcd by Eogineaing Alloys Digesf Inc upper W New J-w...
Journal Articles
Alloy Digest (1980) 29 (8): Bi-19.
Published: 01 August 1980
... for many mis- cellaneous uses among which are : (1) Jigs and furtures, (2) FiIIing blowholes in castings, (3) Metal forming dies, form blocks and joggle jaws, (4) Patterns com- pensated for shrinkage, (5) Magnetic chucks, (6) Repair- ing broken dies, (7) Fixtures for checking, drilling and inspection, (8...
Journal Articles
Alloy Digest (1979) 28 (10): Bi-14.
Published: 01 October 1979
.... Miscellaneous Uses: Belmont alloy 2481 has many miscellaneous uses among which are: (1) Patterns compensated for shrinkage, (2) Fixtures for assembly, checking, die spotting, drilling and inspection, (3) Stripper plates in stamping dies, (4) Holding special or irregular contour parts during machin- ing...
Journal Articles
Alloy Digest (1981) 30 (2): Bi-22.
Published: 01 February 1981
..., low-cost punch plate. Miscellaneous Uses: Indalloy 217-440 has a wide range of miscellaneous uses. Examples follow: (1) Patterns compensated for shrinkage, (2) Fixtures for assembly, checking, die spotting, drilling and inspection, (3) Stripper plates in stamping dies, (4) Holding special or irregular...
Journal Articles
Alloy Digest (1965) 14 (10): Cu-156.
Published: 01 October 1965
.... Soluble oils, because of their greater cooling properties, are recommended as a coolant. For any drilling operations, it is recommended that properly sharpened tools of carbide straight flute be used. If the hole is less than l/2 deep, it may not be necessary to clear the drill; however, if the hole...
Journal Articles
Alloy Digest (1975) 24 (1): Zn-17.
Published: 01 January 1975
... that chips are fed away from the cutting edge as rapidly as conditions permit. In general, high speeds and light cuts yield best results. Carbon-steel drills are used for shallow holes, and high-speed drills are used for deep holes. All drills should have large flutes and thin webs. A 118 deg. point angle...
Journal Articles
Alloy Digest (2020) 69 (5): TS-793.
Published: 01 May 2020
... Drilling with a high-speed twist drill Drill diameter Cutting speed Feed mm in. m/min fpm mm/rev ipr 5 3/16 0.08 0.20 0.003 0.008 5 10 10 15 3/16 3/8 3/8 5/8 22 70 0.20 0.30 25(a) 100(a) 0.30 0.35 0.008 0.012 0.012 0.014 15 20 5/8 3/4 0.35 0.40 0.014 0.016 (a) For coated high speed steel drill, cutting...
Journal Articles
Alloy Digest (1991) 40 (5): SA-37.
Published: 01 May 1991
..., in sections up to 5 thick. The steel s carburized and hardened case has exceptional wear resis- mce. Forms Available: Bar. biller Applications: Gears, shafts. clutchparts, pistonpins. chainrollers andbusbings, wrist pins, boring bars, cutting shanks. jig bars, ratchets, power tool cams, rock drill assemblies...
Journal Articles
Alloy Digest (1961) 10 (8): Co-2.
Published: 01 August 1961
...-hardening alloy that requires an aging treatment at 1500 F for over 300 hours to obtain maximum hardness. Molybdenum is the active precipitating element. At temperatures above 1500 F, structural changes will occur but at an extremeIy low rate, at least up to 1700°F. drilling with a l/2 inch drill and a feed...
Journal Articles
Alloy Digest (1962) 11 (5): CI-15.
Published: 01 May 1962
..., are increased considerably over those speeds used when dry cutting. Safe Speeds and Feeds for High Speed Steel Drills Drill Size, Ft-4 Speed* inch inch rpm l/16 0.002-0.004 4000-6000 34 0.002-0.004 2000-3000 A 0.004-0.006 1100-1600 % 0.006-0.009 700-1100 M 0.008-0.012 500-800 3% 0.012-0.016 300-500 1 0.014...
Journal Articles
Alloy Digest (1984) 33 (1): CS-99.
Published: 01 January 1984
... quenched from the austenitizing temperature and tenipered for one hour at 35&400 F. Forms Available: Flat bars, round bars and rods. hot-rolled strip, cold rolled strip, wire and forgings. Applications: Coil and flat springs. cutting tools, drills, taps, stamps, punt bushings, jigs and fixtures, bumper...
Journal Articles
Alloy Digest (1979) 28 (12): Bi-15.
Published: 01 December 1979
... members in aircraft assembly futures, metal parts in glass magnets in futures and automotive tooling docks. It also is used in a wide range of miscellaneous manufacturing operations where anchoring is necessary, such as in assembly, sub-assembly, drills, inspection and welding fixtures. Aids to Foundry...
Journal Articles
Alloy Digest (1957) 6 (2): TS-55.
Published: 01 February 1957
... Special, when quenched in water or brine from 1450 deg. F., will have the maximum com- bination of hardness and toughness when drawn for one hour at 350-375 deg. F. Forms Available: Bars, rods, and wire. Applications: Taps, drills, reamers, punches, stamps, bushings, knurls, mandrels, threading...
Journal Articles
Alloy Digest (1980) 29 (5): Bi-17.
Published: 01 May 1980
..., such as assembly, sub- assembly, drills, inspections and welding furtures. Molds: OstalIoy 281 is ideal for potting molds for encapsulation of electronic components in plastics. It also is used for molds for plastics, forming sheet plastics, plastic teeth and prosthetic developments. Aids to Foundry Practice...