1-20 of 91 Search Results for

copper no. 107

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Alloy Digest (1972) 21 (10): Cu-259.
Published: 01 October 1972
... COPPER No. 104, 105 and 107 are oxygen-free coppers containing silver to raise the softening temperature and improve the elevated-temperature properties. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as...
Journal Articles
Alloy Digest (1972) 21 (3): Cu-253.
Published: 01 March 1972
... COPPER No. 122 is a deoxidized copper with high residual phosphorus. It is not susceptible to hydrogen embrittlement but has rather low electrical conductivity. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as...
Journal Articles
Alloy Digest (1974) 23 (9): Cu-284.
Published: 01 September 1974
... Copper No. 142 is an arsenical copper deoxidized with phosphorus. Its capacity is excellent for hot forming or cold working and it has excellent joinability characteristics for soldering, brazing and gas-shielded arc welding. Its leading use is tubing for condensers and heat exchangers. This...
Journal Articles
Alloy Digest (1987) 36 (8): Cu-527.
Published: 01 August 1987
...) Yield strength (0.2% offset), psi (MPa) 47000(324) 150000( 1033) I55500( 107 I) Elongation (2 in. or 50 mm), % 20 0 I Rockwell hardness B83 c40 c43 Proportional limit, psi (MPa) - lOOOOO(689) I lOOOO(758) Heat Treatment: Machinability: Stress Relief: Heat Copper Alloy No. C82600 to 4OO F. hold one hour...
Journal Articles
Alloy Digest (1975) 24 (6): Cu-298.
Published: 01 June 1975
... about 10 minutes to one hour; the higher the temperature, the shorter the time. Machinability: Copper No. 147 has excellent machinability. Its machin- ability rating is 85 (Free-Cutting Brass = 100); this is in contrast to a machinability rating of 20 for Copper Numbers 101, 102, 104-107, 109, 110, etc...
Journal Articles
Alloy Digest (1969) 18 (11): Cu-208.
Published: 01 November 1969
... COPPER Alloy No. 752 is a deep drawing grade of nickel silver. It has high resistance to corrosion and tarnish. It is used primarily for drawn, spun and similar cold-worked parts. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties...
Journal Articles
Alloy Digest (1968) 17 (2): Cu-185.
Published: 01 February 1968
... COPPER Alloy No. 770 is a spring quality copper-nickel zinc alloy having high resistance to corrosion. It is recommended primarily for optical goods, springs, resistance wire, hardware and similar products. This datasheet provides information on composition, physical properties, hardness...
Journal Articles
Alloy Digest (1971) 20 (9): Cu-240.
Published: 01 September 1971
... COPPER ALLOY No. 524 is a phosphor bronze having high strength and excellent formability. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fatigue. It also includes information on high temperature performance and...
Journal Articles
Alloy Digest (1981) 30 (3): Cu-414.
Published: 01 March 1981
... 60000 45000 42 107 500 43000 33000 70 88 600 28000 21000 79 62 700 14000 8000 85 32 Heat Treatment: Annealing: Heat Copper Alloy No. C46400 to SOO- 1 lOOoF, cool at any desired rate. Stress Relieving: Heat to 5000F for about one hour, cool at any desired rate. Hardening: This alloy cannot be hardened or...
Journal Articles
Alloy Digest (1982) 31 (7): Cu-440.
Published: 01 July 1982
... of 20 for Copper Numbers 101, 102, 104-107, 109, 110 etc. Thus it is obvious that Copper 1470 is a good choice for applications requiring high conductivity and ex- tensive machining. For general machining, tool geometry and speeds can approximate those used on free-cutting yellow brass. For high...
Journal Articles
Alloy Digest (2013) 62 (11): Cu-826.
Published: 01 November 2013
... MoldMAX XL is a high-strength copper mold alloy with good conductivity. The alloy contains no beryllium and is available in sections as large as 305 mm (12 in.) thick. The alloy’s hardness is comparable to AISI P-20 tool steel, but its thermal conductivity is two to three times higher. This alloy...
Journal Articles
Alloy Digest (1969) 18 (3): SS-222.
Published: 01 March 1969
... acidified copper sulphate test. Scaling or oxidation resistance of No. 635 is slightly less than that of Type 304 at 15OOoF. but superior to Type 304 at 1700oF. General Characteristics: Usually. however. rough machining is performed in the solution annealed condition and light finish machining done...
Journal Articles
Alloy Digest (1961) 10 (9): Cu-107.
Published: 01 September 1961
... chemical composition compressive strength corrosion-resistant alloys elasticity forming dies fracture toughness hardness high-temperature alloys joinability machinability physical properties shear strength tensile properties -DATA ON WORLD WIDE Filing Code: Cu-107 Copper Alloy SEPTEMBER 1961...
Journal Articles
Alloy Digest (2006) 55 (5): Cu-743.
Published: 01 May 2006
... Impact toughness, Izod, typical, 25 mm 14 20 (10-15) diam bar, J (ft . lbf) Hardness, typical, 25 mm diam bar, HB 240 270 Wöhler fatigue, 5 × 107 reversals, typical, 270 (39) 25 mm diam bar, MPa (ksi) See also Tables 1 and 2 and Fig. 1. This alloy does not embrittle at subzero temperatures and has no...
Journal Articles
Alloy Digest (2013) 62 (8): Cu-823.
Published: 01 August 2013
..., MPa (ksi) Fatigue strength, 107 cycles (R=1), MPa (ksi) Elongation, % Impact strength, J (ft·lbf) Hardness, HRC 100 (145) 1170 (170) > 310 (> 45) 5 7 (5) 40 Properties may vary by shape and thickness. DOI: 10.31399/asm.ad.cu0823 these copper mold alloys provide: shorter cycle time; improved plastic...
Journal Articles
Alloy Digest (2004) 53 (8): Cu-721.
Published: 01 August 2004
... machinability physical properties springs tensile properties Wieland-S23 workability thermal properties UNS C68800 Chemical Composition, wt (Reference Chemistry) Cobalt 0.4 Aluminum 3.5 Lead 0.05 max Iron 0.05 max Zinc 23 Aluminum + zinc 25.1 27.1 Copper bal Physical Properties: Density, kg/m3 (lb/in...
Journal Articles
Alloy Digest (2012) 61 (8): Cu-811.
Published: 01 August 2012
... or final design. Published by: ASM International, Materials Park, OH 44073-0002, 440-338-5151 MemberServiceCenter@asminternational.org Fax 440-338-8542 www.asminternational.org Filing Code: Copper August 2012 Cu-811 Wieland K04 is a high conductivity alloy for a variety of electronic and electrical...
Journal Articles
Alloy Digest (2012) 61 (9): Cu-812.
Published: 01 September 2012
.... Published by: ASM International, Materials Park, OH 44073-0002, 440-338-5151 MemberServiceCenter@asminternational.org Fax 440-338-8542 www.asminternational.org Filing Code: Copper September 2012 Cu-812 Wieland-K62 is a high conductivity alloy for a variety of electronic and electrical applications. WIELAND...
Journal Articles
Alloy Digest (2015) 64 (7): Cu-839.
Published: 01 July 2015
... Wieland-K76 (C19010) is copper alloyed with low nickel for good fabricability for parts in the electrical industry. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and bend strength as well as fatigue. It also includes information...
Journal Articles
Alloy Digest (2011) 60 (1): Cu-794.
Published: 01 January 2011
... solutions containing ammonium ions. Specification Equivalents: EN/DIN, no EN standard UNS, <10200 General Characteristics: Wieland-K11 has been designated as oxygen-free copper or oxygen-free electronic copper. Composition Limits. C10100: 99.99 Cu min (there are specific limits in ppm for 17 named elements...