1-20 of 156 Search Results for

coefficient of friction

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Alloy Digest (1992) 41 (3): P-33.
Published: 01 March 1992
... ULTEM 4001 is an unreinforced polyetherimide resin with an internal lubricant. It is wear resistant and it has a reduced coefficient of friction. See also ULTEM 4000 (Alloy Digest CP-21, March 1992) for reinforced resin properties. ULTEM 4001 is available in opaque colors only. This datasheet...
Journal Articles
Alloy Digest (1992) 41 (3): Cp-21.
Published: 01 March 1992
... ULTEM 4000 is a reinforced polyetherimide resin with an internal lubricant. It is wear resistant and has a reduced coefficient of friction. See also ULTEM 4001 for unreinforced resin properties (Filing code P-33, 3/92). This datasheet provides information on physical properties, hardness, tensile...
Journal Articles
Alloy Digest (2013) 62 (6): Cu-819.
Published: 01 June 2013
... ToughMet 2 CX is a Cu-9Ni-6Sn alloy that combines low coefficient of friction with wear resistance. ToughMet alloys are a line of spinodal hardened Cu-Ni antigalling alloys for bearings capable of performing with a variety of shafting materials and lubricants. The alloys combine a high lubricity...
Journal Articles
Alloy Digest (1976) 25 (6): Mo-12.
Published: 01 June 1976
... METCO 505 is a high-molybdenum powder designed to produce plasma flame spray coatings for use as hard bearing surfaces with low coefficient of friction and for resisting wear by abrasive grains or hard surfaces. Its coatings have excellent non-scuffing properties and are compatible with many...
Journal Articles
Alloy Digest (1965) 14 (3): Cu-149.
Published: 01 March 1965
... Revere Alloy 411 is a bearing bronze alloy having good formability, low coefficient of friction, corrosion resistance, and freedom from stress-cracking. (It was formerly known as Revere No. 325.) This datasheet provides information on composition, physical properties, hardness, elasticity, and...
Journal Articles
Alloy Digest (1956) 5 (7): Sn-2.
Published: 01 July 1956
... FEDRATED NO. 3 is a tin-base bearing alloy recommended for moderate to high speeds and loads. It has low frictional resistance, low wear, good running-in properties, good emergency behavior upon failing of lubrication, and lower coefficient of expension than the lead-base alloys. This datasheet...
Journal Articles
Alloy Digest (1976) 25 (4): Zn-27.
Published: 01 April 1976
... MICROZINC Alloy 100 is a zinc-lead-cadmium alloy having good ductility with adequate strength, good resistance to corrosion, and a low coefficient of sliding friction. It is solderable and non-magnetic. Processing differences give three commercial products or classes designated= 101, 102 and 103...
Journal Articles
Alloy Digest (1976) 25 (11): Zn-29.
Published: 01 November 1976
... MICROZINC Alloy 190 is a zinc-copper alloy with good atmospheric corrosion resistance and a low coefficient of sliding friction to eliminate galling in service. It has maximum strength commensurate with good ductility and drawability. Processing differences give two commercial products or classes...
Journal Articles
Alloy Digest (1998) 47 (9): Ni-545.
Published: 01 September 1998
... hydroxide, salt water, and sulfuric acid. It also has a low coefficient to friction to reduce metal-to-metal adhesive wear loss. Colmonoy and Fusewelder are registered trademarks, and Fuseweld, Sprayweld, and Spraywelder are trademarks of Wall Colmonoy Corp. The ahoy-is covered under U.S. patent No...
Journal Articles
Alloy Digest (1957) 6 (7): Al-53.
Published: 01 July 1957
...-scuffing properties, low friction and high wear resistance under conditions of boundary and thin-film lubrication make it particularly suitable. This datasheet provides information on composition, physical properties, hardness, tensile properties, and compressive and shear strength as well as fatigue. It...
Journal Articles
Alloy Digest (1961) 10 (5): Mo-2.
Published: 01 May 1961
..., punching, shearing, and spinning. Drawing dies should be made of aluminum bronze or ochec material wiL a low coefficient of friction. Steel dies should be well lubticated witb light oil. Punching and shearing dies should be kept sharp to avoid lamin- ations and crackin under 0 020 in tii of the sheet...
Journal Articles
Alloy Digest (1977) 26 (10): Al-229.
Published: 01 October 1977
... anti-scuffing properties, low friction and high resistance to wear under conditions of boundary and thin-film lubrication, it is used extensively for large rolling mill bearings. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as fatigue...
Journal Articles
Alloy Digest (1982) 31 (9): Al-240.
Published: 01 September 1982
...-scuffing characteristics, low friction and high resistance to wear under conditions of boundary and thin-film lubrication. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as fatigue. It also includes information...
Journal Articles
Alloy Digest (1984) 33 (3): Al-250.
Published: 01 March 1984
... application because of its anti-scuffing characteristics, low friction and high resistance to wear under conditions of boundary and thin-film lubrication. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength as well as fatigue...
Journal Articles
Alloy Digest (1960) 9 (2): Al-89.
Published: 01 February 1960
... qualities. growth. At elevated tern It has low permanent volume eratures the alloy maintains its mechanical properties E etter than most other alum- inum alloys. Forms Available: Ingots, continuous cast rod. Applications: Pistons, cylinders, sleeves, liners, friction brakes, pre- cision instruments...
Journal Articles
Alloy Digest (1958) 7 (9): Al-69.
Published: 01 September 1958
.... It has low permanent volume growth. (Coeflicient of friction against cast iron at 7O C. is 699% that of the conventional aluminum piston alloys under identical conditions of pressure and lubrication.) At elevated temperatures the alloy main- tains its mechanical properties better than other alu...
Journal Articles
Alloy Digest (1977) 26 (7): Ni-247.
Published: 01 July 1977
... metal. Keep tool clearances to a minimum to provide enough support for the cutting edge and enough bulk of the tool material to conduct heat from the cutting edge. Rake angles should be large enough to minimize chip pressure and thus lower the consequent frictional heat. Machining is aided substantially...
Journal Articles
Alloy Digest (1963) 12 (3): Al-123.
Published: 01 March 1963
... NORAL 162 is an age-hardenable aluminum casting alloy. It has low thermal expansion, good high temperature strength and bearing (frictional) properties. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive, shear, and...
Journal Articles
Alloy Digest (1976) 25 (5): Ni-228.
Published: 01 May 1976
... high-speed steel (cobalt-bearing). Tool clearances should be a mini- mum to allow sufficient support for the cutting edge and sufficient bulk of tool material for carrying away heat generated at the edge. Bake angles should be large enough to reduce chip pressure and consequent frictional heat...
Journal Articles
Alloy Digest (1964) 13 (3): Ni-89.
Published: 01 March 1964
... frictional heat. Cold-drawn material should be used for machining whenever possible because Nickel is er- tremely tough in the hot-rolled or annealed condition. A good grade of water-soluble oil or sulfurized oil should be copiously supplied to rhe cutting edge of the tool. Workability: Practically any shape...