1-10 of 10 Search Results for

Vanadis 30

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Alloy Digest (1999) 48 (1): TS-566.
Published: 01 January 1999
... Vanadis 30 is cobalt alloyed high-performance, high-speed steel made by powder metallurgy. The cobalt addition of approximately 8.5% has a positive influence on the hot strength, hot hardness, temper resistance, and modulus of elasticity. Punches are a suitable application for this alloy. This...
Journal Articles
Alloy Digest (1991) 40 (10): TS-506.
Published: 01 October 1991
...). Austenitize as follows: Temperature Holding Time 980°C (18OO F) 40 min. 1010°C ( 1850°F) 30 min. 1020°C (1870°F) 30 min.* 1050°C (1920°F) 20 min. *This is normally used. 0.08 max. 2max. 0.003/0.012 0.081Q.3 PlO 4601525 140/160 0.08 min. 0.08 max. 2min 2 max. 0.08 min 0.003/0.008 0.2 min. 0.05/0.2 P3o/P40* Plo...
Journal Articles
Alloy Digest (2006) 55 (5): TS-631.
Published: 01 May 2006
... (0.278) Coefficient of linear thermal expansion, 10-6/K (10-6/°F) 20 200 °C (68 390 °F) 10.9 (6.0) 20 400 °C (68 750 °F) 11.7 (6.5) Thermal conductivity, W/m . K (Btu/(ft . h . °F)) 200 °C (390 °F) 30 (17) 400 °C (750 °F) 30 (17) Specific heat capacity, 20 °C (68 °F), 460 (0.11) J/kg . K (Btu/lb . °F...
Journal Articles
Alloy Digest (1995) 44 (3): TS-536.
Published: 01 March 1995
... time: 30 minutes N.B. Holding time = time at hardening temperature after the tool is fully heated throughout. A holding time of less than 30 minutes will result in loss of hardness The tool should not be protected against decarburization and oxidation during hardening. Quenching Media: Forced air/gas...
Journal Articles
Alloy Digest (1998) 47 (10): TS-561.
Published: 01 October 1998
... will be a risk of cracking. rzm- mm- am- 600. 100. 2m, -c llrn lmo sm am 7m 600 KY) am 3m 2m IDo 1 10 loonour Fig. 1 Isothermal transformation TIT graph. Austenitizing temperature 1080 C (1980 F). Holding time 30 min Table 1 Physical Properties, Hardened and Tempered Condition Coeff~cieat of linear...
Journal Articles
Alloy Digest (1998) 47 (12): TS-565.
Published: 01 December 1998
... 0 590 750 Testing temperature Fig.5 Higbtempemmhothardttess 1llQF high-speed steels (HSS). The grindabiliry of Vattadis 60 is equal to or better than that of other high alloyed HSS but samewhat lower chstt that of Vauadis 30. Vanadis 60 has a high hot hardness. Delivered in the soft atmaled...
Journal Articles
Alloy Digest (2020) 69 (11): TS-804.
Published: 01 November 2020
... temperature. Raise the temperature to 850 900 °C (1560 1650 °F) and once again equalize. (b) Austenitizing temperature: 1020 1180 °C (1870 2160 °F). (c) Soaking time: 30 minutes for hardening temperatures up to 1100 °C (2010 °F), 15 minutes for temperatures higher than 1100 °C (2010 °F). Quenching media. (a...
Journal Articles
Alloy Digest (2006) 55 (11): TS-637.
Published: 01 November 2006
... strengths at hardness 62 HRC. Short transverse direction. High-temperature tempered condition DOI: 10.31399/asm.ad.ts0637 Austenitizing temperature is 980 1150 °C (1795 2100 °F), or normally 1050 °C (1920 °F). Holding time. Hold for 30 min up to 1100 °C (2010 °F), or for 15 min above 1100 °C (2010 °F...
Journal Articles
Alloy Digest (2010) 59 (3): TS-687.
Published: 01 March 2010
.../kg · K (Btu/lb · °F) 460 (0.110) (a) Thermal conductivity is very difficult to measure. The scatter can be as high +15%. Mechanical Properties: Temperature °C (°F) 20 (68) 200 (390) 400 (750) Modulus of elasticity, GPa (106 psi) 209 (30) 201 (29.0) 195 (28) Heat Treatment: Soft Annealing. Protect the...
Journal Articles
Alloy Digest (1961) 10 (12): TS-70.
Published: 01 December 1961
... None 49 E 2 1200 46 1300 37 Table 4 -IMPACT TESTS AT ELEVATED TEMPERATURES (Impact MC pieces (0.394 in q. by 2.168 in. long) were anakd with 8 Charpy V notch. AU $aces vcic haAnal u 2200.F.. cooledinairanddrawoullS0 F.fortwohoursPieeswerekld 81 tk cesring cempemure for 30 minus before taring. BesuIts...