1-10 of 10 Search Results for

THIN-FIN

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Alloy Digest (1971) 20 (7): Cu-237.
Published: 01 July 1971
... THIN-FIN is a high-strength, high-conductivity copper containing nominally O.1% cadmium. It is suitable for parts requiring forming and bending only. It possesses high resistance to softening during soldering and thus is a desirable alloy for cores of automotive radiators. This datasheet provides...
Journal Articles
Alloy Digest (1988) 37 (11): Zn-44.
Published: 01 November 1988
... UNS No. Z35840 is a zinc-aluminum-copper alloy that offers exceptionally high strength (58,000 to 64,000 psi tensile strength as cast) at modest cost. It performs best in thin-walled castings (down to 0.10 inch) which means reduced weight and lower material costs when castings are redesigned...
Journal Articles
Alloy Digest (1956) 5 (10): Mg-28.
Published: 01 October 1956
... for the cutting edge. Dry normally used except when taking he cuts at high speeds. Kenxene or mineral seal oil asv;r~k~n4nimal, vegetable or water soluble oils should Corrosion Resistance: This alloy does not corrode in dry air, but develops a thin gray oxide 6lm in moist air. The presence of chlorides in the air...
Journal Articles
Alloy Digest (1957) 6 (8): Mg-33.
Published: 01 August 1957
... not corrode in dry air, but develops a thin gray oxide film in moist air. The presence of chlorides in the air of marine atmospheres increases the amount of surface attack. It is resistant to attack by most alkalis, many organic chemicals, concentrated hydrofluoric acid, pure chromic acid, solutions...
Journal Articles
Alloy Digest (1956) 5 (9): Al-43.
Published: 01 September 1956
... have a 15 deg. clearance. Planer and shaper cools for roughing cuts side rake, 3540 deg. top rake, and twice the clear- should have a 12-15 deg. cop rake, 32-38 deg. side ante used for steel, provided a positive feed is em- rake, and front and side clearances of 8-10 deg. Fin- ployed. Soluble oil...
Journal Articles
Alloy Digest (2005) 54 (1): TS-611.
Published: 01 January 2005
... is guaranteed as well as the soundness. This makes the steel particularly well adapted for mold steel even when polishing or chemical etching is required for surface fin- ish quality. All plates are ultrasonically tested for internal soundness. The ASTM A578-96 acceptance standard is guaranteed. The material...
Journal Articles
Alloy Digest (1958) 7 (7): TS-72.
Published: 01 July 1958
.... After fin- ishing ro sire, the die can then be heat treated in a convenrional manner. HARDWED DIE: When annealing of the die is not practical, then weld in the hardened condition using the following recomtuended procedures: Preheat the dies to as high a temperature as possible but preferably...
Journal Articles
Alloy Digest (2003) 52 (3): SS-879.
Published: 01 March 2003
.... In small or thin sections it can be hardened and strengthened by cold working. It can be machined readily using the procedures normally employed for the chromium-nickel austenitic stainless steels. Nirosta 4438 can be welded readily, and the same composition or one of higher molybdenum should be used...
Journal Articles
Alloy Digest (2004) 53 (10): TS-606.
Published: 01 October 2004
... Transverse 6 Elongation, % Longitudinal 11 Transverse 4 Impact toughness, Charpy U-notch, J/cm2 Longitudinal 16 Transverse 11 Hardness, HRC 45 Machinability: The optimal cutting conditions for NAK-HH vary by machine tools. Cutting tools incorporating the recommended geometry will produce fin- ish machined...
Journal Articles
Alloy Digest (1955) 4 (12): Ni-21.
Published: 01 December 1955
..., % in 2 50-30 20-10 1Yi30000 Under 5/16 inch diameter. 35-17 70-50 :!E Ii0 Table 3 - MECHANICAL PROPERTIES - SHEET Plate, Sheet, Strip, Tensile Strength Condition Hot Rolled, Annealed As-Rolled t0OO&OOO 7u)OO-90000 Cold Rolled, AnnePled 75000-85000 "35" !krin Fin. ErYd9 -- :k%:E lOOoOu-120000 Cold...