1-20 of 114 Search Results for

TENS-50

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Alloy Digest (1960) 9 (7): Al-92.
Published: 01 July 1960
... TENS-50 is a high strength aluminum casting alloy that responds to an age-hardening heat treatment. This datasheet provides information on composition, physical properties, hardness, tensile properties, and compressive, shear, and and bearing strength It also includes information on high...
Journal Articles
Alloy Digest (2016) 65 (6): SA-754.
Published: 01 June 2016
... corrosion is a governing factor. A material appropriate for these applications is S-TEN. (See Alloy Digest SA-548 on S-TEN1.) Corrosion occurs under conditions of 70 °C (158 °F) and 50% H2SO4. S-TEN exhibits corrosion resistance about five times greater than both ordinary steel and COR-TEN and about 10...
Journal Articles
Alloy Digest (1968) 17 (11): SA-233.
Published: 01 November 1968
... EX-TEN steel sheets offer increased protection in certain corrosive applications. Specification Equivalents: SAE J4lOb all grades ML-S-13281B (h(R) Class B Gr.1 Ex-Ten 45 Gr. 2 Ex-Ten 45 and 50 Suggested minimum Inside Radius (r=rhickness) Sheer & Strip Plates to A* Over 0.180 Grade max.Thickness To...
Journal Articles
Alloy Digest (1972) 21 (2): SA-271.
Published: 01 February 1972
... preheating, but steel temperature should never be lower than 50°F during cutting. Corrosion Resistance: COR-TEN C steel has 4 times the atmospheric corrosion resistance of structural carbon steel. Because of thrs greater resistance to atmospheric corrosion, paint and other protective coatings will last...
Journal Articles
Alloy Digest (1972) 21 (11): SA-283.
Published: 01 November 1972
..., Btu/lb/oF (70 to 2120F) Thermal coef. expansion/of (-50 to 15OoF) Modulus of elasticity, psi (Tension) Modulus of rigidity, psi (Torsion) 0.283 1.84 0.12 6.5 x 10-6 28 to 30 x 106 12x106 PROPERTIES Table 1 - TENSILE PROPERTIES* - Plates, Bars, Sheet, Strip and Structurals (Hot-rolled condition...
Journal Articles
Alloy Digest (1972) 21 (7): SA-277.
Published: 01 July 1972
...) Thermal COef. expansion/oF (-50 to l5OoF) Modulus of elasticity, psi (Tension) Modulus of rigidity, psi (Torsion) PROPERTIES Table 1 - TENSILE PROPERTIES* - Plates, Bars and Structurals (Hot-rolled condition Property Tensile strength, min, psi Yield point, min. psi Elongation (2 in), min, % Elongation (8...
Journal Articles
Alloy Digest (1955) 4 (7): SA-31.
Published: 01 July 1955
... has a high endurance limitapproximately 40% greater than char of ASTM-A7 structural carbon steel, and approximately 50% greater than chat of ASTM-All3 struc- tural carbon steel. As indicated by Charpy keyhole nocched- bar impact tests, MAN-TEN has notch toughness or resistance co impact-type loading...
Journal Articles
Alloy Digest (1973) 22 (5): SA-46.
Published: 01 May 1973
.... Composition: Physical Constants: (Approximate) Ladle Density, Ib/cu in Carbon 0.22 mas. Specific gravity Manganese I .25 max. Phosphorus 0.04 mas. Specitic heat, Btu/lb/oF (70 to 212oF) Sulfur 0.05 max. Thermal coef. expansion/OF (-50 to 15OoF) Silicon 0.30 may. Modulus ot elasticity, psi (Tension) Copper...
Journal Articles
Alloy Digest (1962) 11 (8): SA-133.
Published: 01 August 1962
.... Cut, inch Steel Tipped 0.015 l/32 95 375 0.015 l/16 80 300 0.015 l/8 65 260 0.030 1/ 32 70 280 0.030 1/16 60 220 0.030 1/ 8 50 190 Drilling is performed with high-speed steel drills of standard design at cutting speeds of 70-90 sfpm for f drills. Thread chasing can be done at 30-65 sfpm using a lo-15...
Journal Articles
Alloy Digest (1956) 5 (5): SA-42.
Published: 01 May 1956
... following cutting speeds, sfpm, and feeds are recom- mended to machine annealed Hy-Ten X4 : DePTn$f Cut. l/32 1/16 :gi l/2 High Speed Steel Cast Non-Ferrous Cemented Carbide Feed, inches per revolution l/64 l/16 3/32 l/64 l/16 3/32 l/64 l/32 60-65 34-40 ;z z;:5 66-75 55-65 50-58 30-36 60-70 32-38 4 4 Z-E...
Journal Articles
Alloy Digest (1959) 8 (10): SA-90.
Published: 01 October 1959
... Non-Ferrous Cemented Carbide Feeds, inches per revolution lj64 1/16 3.i32 1/a l/16 66-75 3/32 l//64 l/32 - - 60-65 34-40 28-34 2-:i5 55-65 230-260 210-240 50-58 30-36 26-32 75:s5 60-70 50-60 220-250 190-216 42-48 28-34 21-26 52-60 45-53 200-230 170-195 32-38 22-26 16-20 60-70 40-48 32-40 175-200 140...
Journal Articles
Alloy Digest (1970) 19 (1): SA-248.
Published: 01 January 1970
... quenched. tempered as indicated) Tempering Tensile Yield Reduction Brine11 Chqv Temperature Strength Point Elongation of area Hardness Impact oF psi psi O;, in 2 in. 76 3000 Kg ft. Ibs. - - - - 450 260000 230000 10 32 555 - 800 100000 180000 I4 50 429 - 1000 165000 150000 I7 54 341 - 1100 145000 129000 19...
Journal Articles
Alloy Digest (1960) 9 (9): SA-103.
Published: 01 September 1960
... 106 Thermal coef. expansion/ F x lo-6 PROPERTIES Table 1 -. TYPICAL UNHARDENED PROPERTIES - 1 Bar As Rolled Annealed 100000 - 14oooo 95000 - 115000 65000 - 75u00 57000 - 67000 14- 19 16- 24 40 - 50 45 - 60 285 - 302 179 - 223 Table 2 - EFFECT OF MASS Tempering Tensile Yield Reduction Temperature...
Journal Articles
Alloy Digest (2005) 54 (8): SA-550.
Published: 01 August 2005
... (ksi) Elongation in 50 mm or 2 in., minimum 35 requirement, % Hardness, maximum, HB (HRB) 170 (87) See also Fig. 1 4. S-TEN 1 Filing Code: SA-550 Alloy Steel August 2005 S-TEN 1 Corrosion-Resistant Steel Alloy) S-TEN1 is a steel alloy containing copper and antimony to make it more resistant to dew...
Journal Articles
Alloy Digest (1976) 25 (3): TS-298.
Published: 01 March 1976
... spheroidized condition. High-sped steel sit&e-point cutting tools should be ground to 200 side rake, 50 back rake,60side relief, 30 end relief, loo end cuttingedge angle, 100 side cutting-edge angle, and a nose radius of 10% of cut depth. Carbidetipped tools can be used for turning, planing and shaping...
Journal Articles
Alloy Digest (1991) 40 (4): Al-315.
Published: 01 April 1991
... Table 1 - TYPICAL ROOM-TEMPERATURE MECHANICAL PROPERTIES* Tensile strength, ksi (MPa) 33(228) Yield strength, ksi (MPa) 14( 97) Elongation (2 in % 9.0 Brine11 hardness (500 kg load, 1Omm dia. ball) 50 Shearing strength, ksi (MPa) 19(131) Endurance limit (500 x 106 cycles, rotating beam R R Moore test...
Journal Articles
Alloy Digest (2021) 70 (1): CI-77.
Published: 01 January 2021
... listed are mini- ous polymer solution. Expected surface hardness is approxi- mum and maximum across the bar. Hardness values for rect- mately 50 HRC minimum. angular and square bars are a function of their height and width ratios and will be provided by the supplier on request. Tempering. Temper...
Journal Articles
Alloy Digest (1989) 38 (10): P-11.
Published: 01 October 1989
... DSC* max. Specific gravity ASTM D792 Water absorption ASTM D570 24 hour immersion ln 23oC air at 50% R.H h23TWater Linear mold shrinkage EMS Thermal coef. expansion DIN 52328 Heat deflection temperature ASTM D648 @ 66psi(O.46MPa) @ 264psi( 1.82MPa) Maximum usage temperature EMS Longterminair Short...
Journal Articles
Alloy Digest (1961) 10 (8): SA-118.
Published: 01 August 1961
... Impact Temperacute ft. Ibs. Brinell OF V-notch Hardness Fracture 400 27-28 514 60% silky, 20% woody 500 22-25 477 50% 50% 600 17-18 461 50% 50% 700 35-38 375 50% 50% E 38-40 352 50% 50% 51-53 321 50% It 50% 1000 63-65 302 30% 70% Ii 1100 78-79 255 30% 70% 1200 95-98 217 10% 90...
Journal Articles
Alloy Digest (1990) 39 (7): Cp-16.
Published: 01 July 1990
...) 530 (21) Dielecfric constant D150 @ lkHz,50% RH - 3.1 3.1 3.1 Dissipation factor D150 IkHz, 50% RH, 73°F (23°C) - 0.001 0.001 0.001 Volume resistivity, l/16 D257 ohm-cm x 10 1.0 1.0 1.0 Arc resistance, tungsten D495 seconds - - 140 Copyright © ASM International® 1996DOI: 10.31399/asm.ad.cp0016 Table...