1-7 of 7 Search Results for

SD 175

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Publisher: Journals Gateway
Alloy Digest (2005) 54 (9): W-28.
Published: 01 September 2005
... elasticity hardness physical properties SD 170 SD 175 SD 180 SD 185 tensile properties workability Chemical Composition, wt (Nominal) SD 170 SD 175 SD 180 SD 185 Tungsten 90 92.5 95 97 Nickel 7.1 5.4 3.6 2.1 Iron 2.9 2.1 1.4 0.9 Physical Properties: (Typical) Density, kg/m3 (lb/in.3 ) SD 170...
Journal Articles
Publisher: Journals Gateway
Alloy Digest (1976) 25 (2): TS-296.
Published: 01 February 1976
... for l-inch diameter bar in rolling direction. Hardened in oil from 19200F and tempered twice to the hardness shown) Rockwell C hardness Tensile strength, psi Yield strength (0.2% offset), psi Elongation (SD), % Reduction of area, % loo 200 300 4M) 500 600 700 -c 20 30 40 M 60 70 hou T _. . . . . . . . R...
Journal Articles
Publisher: Journals Gateway
Alloy Digest (1962) 11 (5): Co-31.
Published: 01 May 1962
... IXsc type Cylinder Wheel LA302-SD-23366 A120-W2-n7 19A 150-K8-V 19A60-J-V 19A220-1-9-W; A 150-05-VlO C;A605- JS-Vl %A46-J-15-V2 38A46-I-V 87A46-Jll-BB 29A46-F10 Mfg. SterlG Maklin Norton Norton Norton Carborundum Carborundum Sterling Norton Gardner Uaklin Coolant Dry Soluble oil Soluble oil Soluble oil...
Journal Articles
Publisher: Journals Gateway
Alloy Digest (1956) 5 (1): SA-36.
Published: 01 January 1956
... cutting&e angle, 12-16 deg. side cutting-edge angle, and a nose radius of l/32 inch. Use a sulphurized mineral oil as the cutting fluid for high speed steel tools. Cuuina Steeds and Feeds H:gh-Speed Steel ?zyf Feed 1,3; in. /rev. 0.021 175 l/32 0.060 110 Carbide-Tipped Tools Deudlof Feed Sd GiG in in/rev...
Journal Articles
Publisher: Journals Gateway
Alloy Digest (1989) 38 (11): Al-232.
Published: 01 November 1989
... chemical conversion coatings to 7075 are applicable to 7475 alloy. Specification Equivalents: AMS4084A.4207:7475-T61 bareandalcladsheetrespectively. AMS 4085A.4100*: 7475-T761 bate and alclad sheet respectively. AMS 409OA 7474T651 AMS 4089A 7475-T765 1 AMS 4202A 7475-T7351 *MIL-HDBK-SD approval pending...
Journal Articles
Publisher: Journals Gateway
Alloy Digest (1962) 11 (12): TS-127.
Published: 01 December 1962
... char the heating of the material be sd- jusred so that the final working is done above or as near 15OOoF as possible, but in no event below 15000F. Reheat as often as is necessary to finish the forging. After forging, cool slowly in lime or dry ashes. It is always good practice to subject the forging...
Journal Articles
Publisher: Journals Gateway
Alloy Digest (1980) 29 (10): SA-377.
Published: 01 October 1980
... me mm. Preheal and Inlercass lemp ba Sd tie the .- mn,,eratura IS bebw 32OF. WC) 4 Cm be wbmnged arc welded Wnres and fluxes ~rcducq rwenglhr corn. 2. No . ..fdnng ,ho ld ba done rvhen thn amb,cn, mmpcnlure IS below DOF. PamMe 10 me grade lko fci be used Prcheal and mlemass lernperal r* I-20%1...