1-15 of 15 Search Results for

S-STAR

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Alloy Digest (2017) 66 (3): SS-1260.
Published: 01 March 2017
... S-STAR is 420 ESR stainless steel that is capable of high hardness and high polishability. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well...
Journal Articles
Alloy Digest (1961) 10 (12): TS-112.
Published: 01 December 1961
... STAR-M0 M-2 is a tungsten-molybdenum high-speed steel of the 6-6-2 type having good red-hardness quality. This alloy corresponds to AISI type M2. Star-M0 is also available in Free-Machining type, to which sulfur, in the form of alloy sulphides, has been added for better machinability and increased...
Journal Articles
Alloy Digest (1991) 40 (8): TS-504.
Published: 01 August 1991
... dssign. CARPENTER MICRO-MELT5 SPEED-STAR@ FM HiC M-2 ALLOY (Fine Grain Molybdenum-Tungsten High Speed Tool Steel) Carpenter Micro-Melt@ Speed-S@ FM HiC M-2 alloy is a molybdenum tungsten high speed tool steel produced by powder metallurgy techniques. It has a more uniform structure than conventionally...
Journal Articles
Alloy Digest (1965) 14 (12): TS-173.
Published: 01 December 1965
... Red Star Tungsten is a high-carbon low-alloy tool steel having high hardness, good toughness, and keen cutting edge. It is recommended for cutting tools, thread rolling dies, paper knives, etc. This datasheet provides information on composition, physical properties, hardness, elasticity...
Journal Articles
Alloy Digest (1990) 39 (11): P-20.
Published: 01 November 1990
... under actual fue conditions. Table 3 - ELECTRICAL PROPERTIES* Unit Value OF 223 OF 222 OF 170 F 225 I PF 4.4 x 10-s HB HB ASTM Test Property Method Relative temperature index** UL746 Hot wire ignition UL746A High current arc ignition UL746 High volt track rate UL746A Arc resistance D-495 Volume...
Journal Articles
Alloy Digest (1997) 46 (8): Ti-108.
Published: 01 August 1997
... $22, 103 (15) 44.8 (6.5) Fabricability: Beding. litanium tubing can be bent at room ranpaature using star&d bending tooling and techniques. A ma&cl should be used for adequate suppott of the ID when bending thin-walled tubing or if a tight bend radius is needed. The mandrel should be well lubticated...
Journal Articles
Alloy Digest (1962) 11 (1): Ti-5.
Published: 01 January 1962
.... F. Up to 90% nxluction during one heating may be accomplished without dangerofaackingWherlunder5~reductionisto be accomplished on the last heating, the star&g temperamre shod be held below 1650 deg. F. When heating heavy seccioLIs, preheating at 1300 deg. to 1400 deg. F is recommended. COLD WORKING...
Journal Articles
Alloy Digest (1973) 22 (1): Ni-184.
Published: 01 January 1973
... HASTELLOY alloy S is a nickel-base high-temperature alloy having excellent thermal stability, good high-temperature mechanical properties and excellent resistance to oxidation up to 2000 F. This datasheet provides information on composition, physical properties, elasticity, and tensile properties...
Journal Articles
Alloy Digest (1953) 2 (2): Cu-5.
Published: 01 February 1953
... rods having a corn similar to that of the base metal. Can be satis p sition actorily brazed with silver solders using special fluxes. Soft soldering is not satisfactory although improved solder- ing can be done by using ortho-phos boric acid as a dux along with any of the star&r B des smith s solder...
Journal Articles
Alloy Digest (1963) 12 (9): SA-154.
Published: 01 September 1963
... s rario 0.31 0.3-0.6 Thermal coef. expansion, oF x 10-6 (70.8000~) Columbium 6.3 Zirconium 0.02 added Remanence, gausses 3700 Boron 0.003 added Coercive force, oersreds 25 Phosphorus 0.01 max. Sulfur 0.01 max. PROPERTIES Iron Remainder Heat Treatment: Weldability: Anneal: Hear ar: 15000F for 90...
Journal Articles
Alloy Digest (1970) 19 (10): Mo-10.
Published: 01 October 1970
... STRESS-RUPTURE PROPERTiES OF (Dvnamic tests on arc-cast !&inch rods) ARC CAST MOLYBDENUM Test Temperature oF 80 400 800 1200 1600 Modulus of Modulus of Elasticity Elasticity Stress (psi) for Rupture in Designated Time (tension) (torsion) Poisson s Test Stress Relieved Recrystallized psi psi Ratio...
Journal Articles
Alloy Digest (1971) 20 (5): Ni-164.
Published: 01 May 1971
... is readily machinable by conven- tional methods. Tungsten carbide tipped tools are suggested. It also can be machined with HAYNES 98M2 alloy or HAYNES Star J-Metal tools with excellent results, but at lower surface speeds (HAYNES is a registered trademark). High-speed steel tools also can be used. Because...
Journal Articles
Alloy Digest (1981) 30 (11): SS-396.
Published: 01 November 1981
... at the point of cutting. Single-point turning tools of high-speed steel should be ground to S-10 dea. too or rake angle. S-10 deg. back rake, 7-10 deg. fIont clearS-8 deg. side &rance,-8-15 deg. c&t& edge angle, 10-15 deg. lead angle. Chip curlers or chip breakers are recommended. Circular and straight cutoff...
Journal Articles
Alloy Digest (1993) 42 (2): Co-88.
Published: 01 February 1993
... method shouldbeusedwithdiscmionaudcareinthatsomccobalt-base dIoys win boil during welding and cause poxosity. m STAR J-Metal should be preheated and maintained at 1500┬░F (816oC) minimum during welding, followed by tiunace cooling. Staudard weld joints are reamurmded. Machining: with Ihe proper machine...
Journal Articles
Alloy Digest (1957) 6 (9): TS-62.
Published: 01 September 1957
... The sad should be reheated befora it awls below 1750 deg, as strains set up due to cold work art often harmful Specification Equivalents: AISI Type Tl s&Tm =l 2 chip EEiEsJz SpCCidHS &ttiFi Superior Crucible ViflcO star zalith Fir+ Sterling Clarke All&eke Ludlum Utuvepl-Cyckaps Vanadmm Alloys RaM Bracburn...