1-9 of 9 Search Results for

Mars 190

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Alloy Digest (2012) 61 (10): SA-664.
Published: 01 October 2012
... Mars 190 is a quenched and high tempered armor steel. This datasheet provides information on composition, physical properties, and hardness. It also includes information on forming, heat treating, and joining. Filing Code: SA-664. Producer or source: Industeel USA, LLC. Copyright © ASM...
Journal Articles
Alloy Digest (2021) 70 (3): SA-869.
Published: 01 March 2021
... Industeel Mars 380 (earlier known as Industeel Mars 190) is a low-carbon, Ni-Cr-Mo-V-B, alloy protection steel that is used in the quenched and tempered condition (typical hardness = 380 HBW). It is used as rolled homogeneous armor for ballistic protection and evaluation of armor-defeating...
Journal Articles
Alloy Digest (2021) 70 (1): SA-876.
Published: 01 January 2021
... (1.18) Mars 240 6.5 (0.256) min 28% 23% Stanag 4569 Level 3a 0° 8.5 (0.335) Stanag 4569 Level 4 0° Mars 240 6.5 (0.256) min 15% 10% Mars 190 8 (0.315) min 30% 25% Mars 190 15 (0.591) min 35% 30% Source: Mars 600, Industeel ArcelorMittal, 2016 Table 4 Bending conditions Thickness Minimum radius (R) of...
Journal Articles
Alloy Digest (2012) 61 (12): SA-668.
Published: 01 December 2012
...-heating at 150 200 ºC (300 390 ºF) are recommended. Weldability: Mars 190 can be weld assembled without any preheating or stress-relieving up to 20 mm (0.8 in.) thicknesses. The producer recommends a pre- and post-heating at 150 200 ºC (300 390 ºF). The edges of cut parts or plates must be ground to...
Journal Articles
Alloy Digest (2012) 61 (11): SA-667.
Published: 01 November 2012
... ºF). The pre-heating and post-heating temperature should never exceed 190 ºC (370 ºF). Specification Equivalents: France NF A36-800 Germany TL 2350 Quality Z UK DEF STAN 95-24 US MIL A 12560 CL 4a (420 460 HB) General Characteristics: This alloy is an armor steel dedicated to modern vehicle...
Journal Articles
Alloy Digest (1965) 14 (2): TS-12.
Published: 01 February 1965
... speeds, feeds, and depths of cut are recommended: Depthof Feed Cutting Speed, sfpm cut, inch in/rev. II@ Speed SteeI Carbide l/32 l/64 54-60 208-2 34 l/l6 l/32 41-46 170-190 l/8 l/32 35-40 151-170 114 1/a 33-37 160-180 m l/a4 20-23 104-118 l/2 l/32 17-20 100.110 Recommended cutting fluids are: Operation...
Journal Articles
Alloy Digest (1968) 17 (10): Ni-139.
Published: 01 October 1968
... at 18O-190 F for 30-90 minutes immersion time. After pickling, rinse in hot water and neutralize in a I-Z% by volume ammonia solution. Specification Equivalents: ASTM Bl60 SAE-AMS 5553 ASTM Bl6l ASME SB- 160 ASME SB-1Gl ASTM BIG2 ASME SB-162 ASTM B163 ASME SB-I63 (Nickel 200 conforms to the above...
Journal Articles
Alloy Digest (1961) 10 (8): SA-118.
Published: 01 August 1961
... Tensile Yield Reduction Izod Temperature Strength Point Elongation of Area Brine11 Impact OF psi psi % in 2 % Hardness ft. lbs. 400 240000 209000 12 48 477 10 500 224000 200000 12.5 461 207000 188000 13 :: 429 21 600 7 190 75 4 57.5 388 z 800 174000 160000 15 60 363 9 56 45 6 2.5 31 lz: 1000 140000...
Journal Articles
Alloy Digest (1955) 4 (5): Pb-2.
Published: 01 May 1955
... above 190°F.. is the aUo9 most geneally used for proof casting There are ocher applications for which the properties of CFXROSAFE mar he used co an advancaxe. One aoolicarion of the alloy is co use it as a hller behi;d deli& -parts to be machined or ground in profiling or duplicating machines. ne DEUT...