1-20 of 749 Search Results for

LOW RESISTANCE 180 ALLOYS

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Alloy Digest (1989) 38 (5): Cu-546.
Published: 01 May 1989
... Low resistance alloys are used for applications where low to moderate electrical resistivity is required, as in various lead wires, for example. The numbers 30, 60, 90 and 180 designate the specific resistivities (ohm/cir mil ft) of the respective alloys of this family. This datasheet provides...
Journal Articles
Alloy Digest (1978) 27 (2): Cu-348.
Published: 01 February 1978
... DRIVER 180 ALLOY is a copper-nickel alloy for use where moderate electrical resistance is required. The number designation refers to its specific resistivity (180 ohms/cir mil/ft) which is combined with a fairly low coefficient of resistance (180 x 10^-6 per C). Its maximum recommended operating...
Journal Articles
Alloy Digest (2009) 58 (11): Fe-149.
Published: 01 November 2009
... Bimetal) KANTHAL® 180 R05 Chemical Composition, wt (Nominal) High-expansive component 411 Low-expansive component 450 Manganese 74 0.12 Nickel 12 36.8 Copper 14 Iron bal bal Physical Properties: Density, kg/m3 (lb/in.3) 8200 (0.295) Electrical resistivity, bimetal, Designation 180 R05, · m ( circular...
Journal Articles
Alloy Digest (1977) 26 (7): Cu-337.
Published: 01 July 1977
... low electrical resistivity and a relatively high tempera- ture coefficient of resistivity. This alloy is one of a series of four Radio Alloys produced by the manufacturer; in fact, it is the first member of the series which has resistivities of 30, 60,90 and 180 ohms per circular mil per foot...
Journal Articles
Alloy Digest (1977) 26 (8): Cu-339.
Published: 01 August 1977
... DRIVER 60 ALLOY is a copper-nickel alloy for use where fairly low electrical resistance is required. The number designation corresponds to its specific resistivity (60 ohms/cir mil/ft) which is combined with a fairly high temperature coefficient of resistance. Its maximum recommended operating...
Journal Articles
Alloy Digest (1977) 26 (11): Cu-343.
Published: 01 November 1977
... DRIVER 90 ALLOY is a copper-nickel alloy for use where only moderately low electrical resistance is required. The number designations refers to its specific resistivity (90 ohms/cir mil/ft) which is combined with a moderate coefficient of resistance. Its maximum recommended operating temperature...
Journal Articles
Alloy Digest (1975) 24 (2): Ni-215.
Published: 01 February 1975
... Alloy 505 (As Cast or Age-Hardened)t4) 15-25 15-25 lo-20 8-12 50-100 Nickel-Copper Alloy 506 2540 25-35 40-60 10-20 90-180 *Operating speeds for rough cuts should be on the low side of the indicated speed range. Speeds for light finishing cuts should be near the high side of the range. Speeds cited for...
Journal Articles
Alloy Digest (1975) 24 (1): Ni-214.
Published: 01 January 1975
... or Tapping Turning(l) NickelCopper Alloys 4 10 and 4 11 40-50 40-50 40-70 15-25 130-225 *Operating speeds for rough cuts should be on the low side of the indicated speed range. Speeds for light finishing cuts should be near the high side of the range. Speeds for high-speed tools can be increased...
Journal Articles
Alloy Digest (1962) 11 (5): Cu-117.
Published: 01 May 1962
... Midohm is a copper-nickel, heat resistant alloy having a maximum operating temperature of 400 deg F. It is normally used for resistor and potentiometer applications where low specific resistance is required. This datasheet provides information on composition, physical properties, and tensile...
Journal Articles
Alloy Digest (1997) 46 (6): Ni-528.
Published: 01 June 1997
... Qll 8.1 8.1 17% mN 1958 (1070) 2264(1240) p64(lt40) Seefabk 1 StzTabk2 SeeTabk3 seCTabk4 wi sticlcous mm (in.) Polarity Reheat C (OF) 160-200 260-280 100% Ar at 17-19 Mnin(35-4OCFH) 13-19 ( I&34 ) DCRF 250-300 (482-572) Corrosion and Wear Properties: Weldability: The high silicon and low boron in the...
Journal Articles
Alloy Digest (2019) 68 (1): Ni-750.
Published: 01 January 2019
... to work- hardening, low cutting speeds and appropriate feed rates should be used and the tool should always be engaged. Sufficient chip depths are important to get below the work-hardened surface layer. Weldability Welding Technique. This alloy can be welded in most applications with VDM FM 59 using...
Journal Articles
Alloy Digest (1961) 10 (10): SS-122.
Published: 01 October 1961
.... The low thermal conductivity of the alloy makes it most important to have the cutting fluid flood both the tool and the work. Sulfa-chlorinated petroleum oil containing active sulphur and about 8 to 10 per cent fatty oil is recommended for high speed steel tools. Water-soluble cutting fluids are...
Journal Articles
Alloy Digest (2016) 65 (6): Ni-725.
Published: 01 June 2016
... higher work hardening rate than austenitic stainless steels. After cold working with more than 10% deformation or more than 5% for applications above 900 °C (1652 °F), the material should be solution annealed. Machinability: VDM Alloy 617 B should be machined in the solution annealed condition. Low...
Journal Articles
Alloy Digest (1997) 46 (5): Ni-526.
Published: 01 May 1997
... HPM Evanohm S is a nickel-base alloy having low-temperature coefficient of resistance and high electrical resistivity. This datasheet provides information on composition, physical properties, and tensile properties. It also includes information on heat treating. Filing Code: Ni-526. Producer or...
Journal Articles
Alloy Digest (2009) 58 (4): Cu-768.
Published: 01 April 2009
... Wieland-F12 is a resistance alloy with a low coefficient of electrical resistance. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating...
Journal Articles
Alloy Digest (2002) 51 (3): Al-324.
Published: 01 March 2002
... AlcoTec Filler Metal 4643 is a reduced-silicon, magnesium-added filler metal used to weld the 6xxx series alloys. Welds meet the high mechanical properties of the 6xxx series, particularly in multipass welding and when low dilution exists. There is no advantage in using 4643 compared to 4043 or...
Journal Articles
Alloy Digest (1962) 11 (3): SA-126.
Published: 01 March 1962
... ESCO Alloy 12M is a low alloy, medium carbon content, hard, shock and impact-resisting steel recommended for heavy duty cast parts. Minor chemical composition variations and heat treatment are employed in order to develop specific properties. This alloy possesses exceptional toughness at low...
Journal Articles
Alloy Digest (1962) 11 (4): SA-127.
Published: 01 April 1962
... elasticity fracture toughness hardness heat treatability joinability low-temperature alloys notch-impact resistance physical properties tensile properties workability COLTUF 28 Filing Code: SA-127 Steel -Alloy APRIL 1962 -DATA ON WORLD WIDE METALS AND ALLOYS Pnblisbed by Engineering Alloys Digest...
Journal Articles
Alloy Digest (2004) 53 (10): Fe-132.
Published: 01 October 2004
... Carpenter Low Expansion 39 alloy is a 39% nickel iron alloy with a low rate of thermal expansion useful to temperature ranges up to 316 deg C (600 deg F). This datasheet provides information on composition, physical properties, and tensile properties. It also includes information on joining...
Journal Articles
Alloy Digest (1992) 41 (12): Cu-537.
Published: 01 December 1992
... 200600 60-180 .002-.OlO .005-.025 125-500 40-150 .002-.OlO .005-.025 200600 60-180 .002-.OlO .005-.025 125-500 40-150 .002-.OlO .005-.025 Note: Reduce speed and feed when using reamers or milling cutters smaller than approximately 3/16 in. diameter. Use low end of cutting speed range when tapping holes...