1-8 of 8 Search Results for

COLONIAL no. 6

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Alloy Digest (1960) 9 (6): TS-94.
Published: 01 June 1960
... COLONIAL No. 6 is an oil hardening, non-deforming, general purpose tool and die steel. It has good combination of abrasion resistance, hardness and toughness. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well...
Journal Articles
Alloy Digest (1956) 5 (12): TS-53.
Published: 01 December 1956
... COLONIAL NO. 4 is a water-hardening, high carbon tool steel containing about 3 1/2% tungsten. This datasheet provides information on composition and hardness. It also includes information on forming, heat treating, and machining. Filing Code: TS-53. Producer or source: Vanadium-Alloys Steel...
Journal Articles
Alloy Digest (1959) 8 (2): TS-79.
Published: 01 February 1959
...., tempered 1 hour) Tempering Temperature OF. Room 200 ;: 400 450 500 550 600 700 800 Relative Torsional Impact values ft. Ibs. 20 2: 115 100 60 2 41 2; Table 3- END QUENCH HARDENABILITY J-Distance in l/16 inch 0 1 : 4 6 8 2 24 RockwelI c Hardness 1525°F. Quench 1625°F. Quench 67.5 66.0 65.0 46.0 50 ;z 5010...
Journal Articles
Alloy Digest (1957) 6 (2): TS-55.
Published: 01 February 1957
... speed steel single point cutting tools should be ground to 20 deg. side rake, 5 deg. back rake, 6 deg. side relief, 3 deg. end relief, 10 deg. end cutting-edge angle, 10 deg. side cutting-edge angle, and a nose radius of 109 of cut depth. Carbide-tipped tools can be used for turning, planing...
Journal Articles
Alloy Digest (1955) 4 (9): TS-38.
Published: 01 September 1955
... (Jessop) Badger ( Latrobc) Teenax- (Simonds) Wando (Universal-Cyclops) Colonial No. 6 (Vanadium Alloys) Vulcan Oil Hardening (Vulcan) General Characteristics: UHB-46 is an oil hardening, non-deforming alloy tool steel of excellent toughness and wear resistance. It is deep hardening and will withstand many...
Journal Articles
Alloy Digest (2023) 72 (6): CS-251.
Published: 01 June 2023
... is insufficient to justify the additional cost of heat treatment. 1038 and 1038H are among the most widely used steels for threaded fasteners. Their popularity stems from their excellent cold-heading properties, low cost, and wide availability. Source: Ref 1 6 General Characteristics Medium-to-high strength; good...
Journal Articles
Alloy Digest (2023) 72 (5): CS-246.
Published: 01 May 2023
... is not justified. Owing to their low hardenability their use in the quench and tempered condition is not recommended for large sizes, as the improvement in mechanical properties over the normalized condition is insufficient to justify the additional cost of heat treatment. Source: Ref 1 6 General Characteristics...
Journal Articles
Alloy Digest (2023) 72 (5): CS-248.
Published: 01 May 2023
... treatment. Source: Ref 1 6 General Characteristics Medium-to-high strength; low hardenability. 1053 has higher hardenability than 1050 because of a higher manganese content; poor corrosion resistance; good hot formability; poor cold formability; fair machinability; poor weldability. Chemical Composition...