Search Results for ASTM A 533 GRADE B

ASTM A 533 Grade B is a manganese-molybdenum-nickel alloy steel for use in the quenched-and-tempered condition for plate for the construction of pressure vessels and other pressure equipment. It is used in 6 to 12-inch sections and is the most widely used steel for nuclear reactor pressure vessels. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as fracture toughness. It also includes information on forming, heat treating, machining, and joining. Filing Code: SA-328. Producer or source: Alloy steel mills and foundries.

Rio Tinto 319.2 is a heat-treatable, Al-Si-Cu casting alloy (3xx.x series). It is available in the form of ingots for remelting, for the production of sand and permanent mold castings. Alloy 319.0 exhibits very good castability and pressure tightness, moderate strength, and good high-temperature properties. It offers good strength in the as-cast condition and is often used that way. However, it is possible to increase strength considerably by heat treatment. In applications that experience high temperatures, as in engine components, it is common to employ a T5, T7, or O treatment. These treatments tend to stabilize the casting and reduced dimensional changes in the component caused by high temperatures in service. This datasheet provides information on composition, physical properties, elasticity, and tensile properties. It also includes information on corrosion resistance as well as casting, heat treating, machining, and joining. Filing Code: Al-474. Producer or source: Rio Tinto Limited.

CDA C18700 is a copper-base alloy containing lead (nominally 1.0%). The lead is added to impart free-cutting properties to the metal. Although the lead lowers the electrical conductivity of CDA C18700 slightly below that of tough-pitch copper, it still has high electrical conductivity well within the limits needed for most current-carrying requirements. Typical uses comprise electrical motor and switch parts, electrical connectors and screw-machine parts requiring high conductivity. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Cu-533. Producer or source: Copper and copper alloy mills.

Mecasteel 75 (minimum yield strength 75 ksi) is a high-strength prehardened steel that can be used in substitution for conventional steels, such as AISI 4130, in the manufacture of massive steel components such as machines, hydraulic systems, and pumps. This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and joining. Filing Code: SA-700. Producer or source: Industeel USA, LLC.

Diros 500 is a fine-grained pressure vessel steel delivered in two grades: one as high strength, the other for sour service. This datasheet provides information on composition, physical properties, and tensile properties as well as fracture toughness. It also includes information on forming, heat treating, and joining. Filing Code: SA-630. Producer or source: Dillinger Hütte GTS.

ATI 310S is a 25Cr-20Ni austenitic stainless steel that is typically used for elevated temperature applications. Owing to its higher chromium and nickel contents the alloy provides comparable corrosion resistance, superior resistance to oxidation, and the retention of a larger fraction of room temperature strength than the common austenitic stainless steels such as Type 304. This datasheet provides information on composition, physical properties, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SS-1328. Producer or source: ATI.

Superelso 500HR, also known as SE 500HR, is a high yield strength, quenched-and-tempered alloy for wet H2S service in the oil and gas industry. This datasheet provides information on composition, hardness, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and joining. Filing Code: SA-554. Producer or source: Industeel USA, LLC.

BRUSH Alloy 165 has slightly less yield and fatigue strengths than the somewhat higher beryllium-content copper-beryllium alloy. It is cheaper and may be substituted when design requirements are less demanding. It is easily worked to provide complex shapes. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fatigue. It also includes information on corrosion resistance as well as forming, heat treating, and joining. Filing Code: Cu-532. Producer or source: Brush Wellman Inc..

NITRONIC 30 is a nitrogen-strengthened stainless steel with a good combination of strength, corrosion and wet abrasive wear resistance and economy. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness, and deformation. It also includes information on corrosion and wear resistance as well as forming, heat treating, and joining. Filing Code: SS-533. Producer or source: Armco Advanced Materials Corporation.

1017 and S17C are wrought low-carbon (C = 0.15–0.20%) non-alloy steels that are used in the as rolled, normalized, or cold worked condition. These steels are widely used for lightly and moderately stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and also for applications where a combination of low-to-medium strength, excellent cold formability, and excellent weldability are required. They may also be used in the carburized or carbonitrided, and subsequently quench hardened and tempered condition for parts requiring a hard, wear-resistant surface, but with little need for increased mechanical properties in the core. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: CS-234. Producer or source: Data Survey.

1021, 1022, C20C, and C20GC are wrought low-carbon non-alloy steels that are used in the as rolled, normalized, cold worked, or quenched and tempered condition. They are widely used for lightly and moderately stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and also for applications where a combination of low-to-moderate strength, good ductility, good cold formability, and good weldability are required. 1021 and 1022 may also be used in the carburized or carbonitrided, and subsequently quench hardened and tempered condition for parts requiring a hard, wear-resistant surface, but with little need for increased mechanical properties in the core. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: CS-223. Producer or source: Data Survey.

1045, 1045H, 1046, C45, C45E, and C45R are wrought medium-carbon non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. 1045, 1045H, 1046, C45E, and C45R may also be flame or induction hardened. These steels are widely used for moderately and highly stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and where the expense of an alloy steel is not justified. Owing to their low hardenability their use in the quench hardened and tempered condition is not recommended for large sizes as the improvement in mechanical properties over the normalized condition is insufficient to justify the additional cost of heat treatment. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joinability. Filing Code: CS-217. Producer or source: Data Survey.

1018 and C17 are wrought low-carbon non-alloy steels that are used in the as rolled, normalized, or cold worked condition. They are widely used for lightly and moderately stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and also for applications where a combination of low-to-medium strength, good cold formability, and excellent weldability are required. They may also be used in the carburized or carbonitrided, and subsequently quench hardened and tempered condition for parts requiring a hard, wear-resistant surface, but with little need for increased mechanical properties in the core. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: CS-227. Producer or source: Data Survey.

1038 and 1038H are wrought medium-carbon non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. 1038 and 1038H may also be flame or induction hardened. These steels are widely used for moderately and highly stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and where the expense of an alloy steel is not justified. 1038 and 1038H are one of the most widely used steels for threaded fasteners. Their popularity stems from their excellent cold-heading properties, low cost and availability. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: CS-230. Producer or source: Data Survey.

1023 and S22C are wrought low-carbon non-alloy steels (C = 0.20–0.25%, Mn = 0.30–0.60%) that are used in the as rolled, normalized, or cold worked condition. These steels are widely used for lightly and moderately stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and also for applications where a combination of low-to-medium strength, good cold formability, and good weldability are required. They may also be used in the carburized or carbonitrided, and subsequently quench hardened and tempered, condition for parts requiring a hard, wear-resistant surface, but with little need for increased mechanical properties in the core. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: CS-235. Producer or source: Data Survey.

1034, 1035, 1037, C35, C35E, and C35R are wrought medium-carbon non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. 1034, 1035, 1037, C35E, and C35R may also be flame or induction hardened. These steels are widely used for small, moderately stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and also for applications where a combination of moderate strength and good toughness is required. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as heat treating, machining, and joining. Filing Code: CS-215. Producer or source: Data Survey.

1050, 1053, C50, C50E, and C50R are wrought medium-carbon non-alloy steels that are used in the normalized, cold worked, quenched and tempered, or austempered condition. 1050, 1053, C50E, and C50R may also be flame or induction hardened. These steels are widely used for moderately and highly stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and where the expense of an alloy steel is not justified. Owing to their low hardenability, their use in the quench hardened and tempered condition is not recommended for large sizes, as the improvement in mechanical properties over the normalized condition is insufficient to justify the additional cost of heat treatment. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: CS-218. Producer or source: Data Survey.

1030, C30, C30E, and C30R are wrought medium-carbon non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. 1030, C30E, and C30R may also be flame or induction hardened. These steels are widely used for small, moderately stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and also for applications where a combination of moderate strength and good toughness is required. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: CS-214. Producer or source: Data Survey.

1016, C16E, and C16R are wrought low-carbon non-alloy steels that are used in the as rolled, normalized, or cold worked condition. These steels are widely used for lightly and moderately stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and also for applications where a combination of low strength, excellent cold formability, and excellent weldability are required. They may also be used in the carburized or carbonitrided, and subsequently quench hardened and tempered condition for parts requiring a hard, wear-resistant surface, but with little need for increased mechanical properties in the core. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: CS-226. Producer or source: Data Survey.

1015, C15E, and C15R are wrought low-carbon non-alloy steels that are used in the as rolled, annealed, normalized, or cold worked condition. These steels are widely used for lightly stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and also for applications where a combination of low strength, excellent cold formability, and excellent weldability are required. They may also be used in the carburized or carbonitrided, and subsequently quench hardened and tempered condition for parts requiring a hard, wear-resistant surface, but with little need for increased mechanical properties in the core. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: CS-225. Producer or source: Data Survey.