1-20 of 54 Search Results for

AISI 1040

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Alloy Digest (1971) 20 (6): CS-41.
Published: 01 June 1971
... AISI 1040 is a medium-carbon steel used in the hot-rolled, normalized, oil quenched and tempered or water quenched and tempered condition for general purpose engineering and construction. It provides medium strength and toughness at low cost. This datasheet provides information on composition...
Journal Articles
Alloy Digest (1988) 37 (4): CS-120.
Published: 01 April 1988
... into contact with moisture and air at room temperature. If salts are present. the corrosion rate is increased. The steel is attacked readily by acids, but is somewhat resistant to alkalis at ordinary temperatures. Specification Equivalents: AISI 1040. UNS GlO400. ASTM A 29(1040). A 510(1040). A 519(1040...
Journal Articles
Alloy Digest (1974) 23 (11): CS-22.
Published: 01 November 1974
... 2. Machinability and Grindability: Constant-pressure lathe turning tests on bar specimens of USS FREMAX 45 steel show that this plate steel machines 30 to 50% better than AISI 1040 or AISI 1045 plate steels. Because the cutting temperature developed when machining USS FREMAX 45 steel is lower than...
Journal Articles
Alloy Digest (2023) 72 (5): CS-246.
Published: 01 May 2023
...) above the nitrocarburizing temperature. Source: Ref 73, 82, 85 Fig. 43 Hardness profile for various ion-nitrided materials. 1, gray cast iron; 2, ductile cast iron; 3, AISI 1040; 4, carburizing steel; 5, low-alloy steel; 6, nitriding steel; 7, 5% Cr hot-worked steel; 8, cold-worked die steel; 9...
Journal Articles
Alloy Digest (1981) 30 (3): SS-383.
Published: 01 March 1981
... of 90% of yield strength (0.2% offset) follows: Grade Time to Failure, hours AISI Type 304 50-400 AJSI Type 316 300600 UHB Stainless 44LN > 3000, no failure UHB Stainless 44LN possesses good resistance to stress-corrosion cracking in sulphidic environments containing H2S. Corrosion in 5% NaCl saturated...
Journal Articles
Alloy Digest (1986) 35 (6): SS-471.
Published: 01 June 1986
... Copyright © ASM International® 1996 Table 3 - CORROSION-RESISTING CHAR.4CTERISTICS A. STRESS-CORROSION CRPICKING Stress: 9OTc of 0.2crC. Offset j ield Strength Environment: 405, CaCI: at 100°C Steel Time to Stress-Crack Failure. Hours AISI Type 304 PIISI Type 316 .AVESTA 44 LN IOU-300 00-500 No iailure...
Journal Articles
Alloy Digest (2022) 71 (2): CS-216.
Published: 01 February 2022
... and Alloys CS-216 / 8 Table 15 Recommended machining data Turning, single point and box tools High speed steel tool Uncoated carbide tool Depth of cut Tool material Speed Feed Tool material Speed Brazed Indexable mm ISO m/min mm/rev ISO m/min m/min (in.) (AISI) (fpm) (ipr) (C) (fpm) (fpm) Treatment...
Journal Articles
Alloy Digest (1991) 40 (3): TS-503.
Published: 01 March 1991
... electric discharge machining and grinding characteristics (comparable to AISI D2 or M2 grades). Stress tempering at 1000°F for 1 hour is recommended. Welding: If repair welding is necessary, preheating and post weld heat treatment are required as for AIS steel. General Characteristics: ASP 23 provides...
Journal Articles
Alloy Digest (1992) 41 (8): TS-512.
Published: 01 August 1992
... THYRAPID 3341 is similar to AISI M2, but adds sulfur. It is general purpose high-speed tool steel with good toughness, red hardness, and excellent machinability. This datasheet provides information on composition, physical properties, and hardness. It also includes information on forming, heat...
Journal Articles
Alloy Digest (2001) 50 (3): SS-820.
Published: 01 March 2001
... will be a problem in corrosion environ- ments, use the lower carbon grade of the alloy, unless the welded assembly can be heated to 1040 °C (1900 °F) and water quenched. Although it is recommended that welding should be done with electrodes of the same composition, electrodes of AISI type 310 stainless steel can...
Journal Articles
Alloy Digest (1999) 48 (2): TS-567.
Published: 01 February 1999
... Uddeholm AISI D2 is a high-carbon, high-chromium, air-hardening tool and die steel capable of great hardness and high resistance to abrasive wear. It is nondeforming and is also somewhat corrosion resistant. This datasheet provides information on composition, physical properties, hardness...
Journal Articles
Alloy Digest (1994) 43 (5): SS-566.
Published: 01 May 1994
... URANUS 52N is a nitrogen-alloyed duplex stainless steel improved in stress-corrosion cracking resistance and with pitting and crevice corrosion resistance better than AISI Type 317L. Applications include handling phosphoric acid contaminated with chlorides and in flue gas desulfurization scrubbers...
Journal Articles
Alloy Digest (1968) 17 (5): TS-205.
Published: 01 May 1968
... toughness, the tempering temperature can be raised to 450°C (842°F) and kept at this temperature for 2-3 hours. Machinability: In the annealed state Double Six has a machin- ability rating about 55% of a 1% carbon tool steel and about 35% of AISI Blll2. Grind high speed steel single point cutting tools...
Journal Articles
Alloy Digest (2009) 58 (10): SA-608.
Published: 01 October 2009
... Crucible #135 Modified is a variation of AISI 4140 for nitriding the surface for hardness and abrasion resistance. This datasheet provides information on composition, physical properties, and elasticity. It also includes information on heat treating, joining, and surface treatment. Filing Code: SA...
Journal Articles
Alloy Digest (1988) 37 (8): SS-497.
Published: 01 August 1988
... Hardening Alloy may also be brazed. Corrosion Resistance: Corrosion resistance of AL 17-4 Recipitation Hardening Alloy is comparable to that of AISI Type 304 stainless in most media. It is generally superior to the hardenable AISI 400 series. In applications wherechloride stress-corrosion cracking is apossi...
Journal Articles
Alloy Digest (1993) 42 (12): SS-558.
Published: 01 December 1993
... is higher than that of AISI 316 or 317L. REMANIT 4462 can be used for sea-water ser- vice, e.g. for heat exchangers in coastal areas or in desalination plants at moderate temperatures. Owing to the duplex structure, resistance against stress-corro- sion cracking and corrosion-fatigue is very high SUe5s...
Journal Articles
Alloy Digest (1988) 37 (5): SS-494.
Published: 01 May 1988
... - CORROSION OF AISI TYPE 316 and AL-6XN@ BASE METAL IN VARIOUS BOILING MEDIA Test Corrosion. mils] year Environment Type 316 AL-6XN@ 20% Acetic acid 0. I2 0.14 45% Formic acid 10.92 4.55 10yo Oxalic acid 40.08 10.92 20% Phosphoric acid 6.96 0.26 IOyc Sulfamic acid 63.60 29.57 10% Sulfuric acid 372.00 84.40...
Journal Articles
Alloy Digest (2010) 59 (11): SS-1078.
Published: 01 November 2010
... temperature range: 50 to 300 ºC ( 58 to 572 ºF); and improved stress corrosion resistance compared to AISI Type 304SS. Products Available: Forms: sheets, blanks, strips. Thicknesses: 0.7 up to 10 mm (0.028 up to 0.394 in.) Width: up to 200 mm (7.87 in.) According to thickness. Finish: cold rolled or hot...
Journal Articles
Alloy Digest (2009) 58 (7): TS-681.
Published: 01 July 2009
... of approximately 500 °C (930 °F). Temper a minimum of two times; see tempering graph in Fig. 4. See also the continuous time-temperature transformation diagram in Fig. 5. Fig. 4 Tempering graph Specification Equivalents: UNS T20811 1.2343 EN ISO 4957 X37CrMoV5-1 AISI H11 Fig. 5 Continuous time-temperature...
Journal Articles
Alloy Digest (2013) 62 (6): TS-718.
Published: 01 June 2013
... DIMO 2311 is a modified version of 1.2311 according to Stahl-Eisen Liste and similarly, a modified version of AISI P20 according to ASTM A681. This datasheet provides information on composition, physical properties, and hardness. It also includes information on forming and heat treating. Filing...