1023 and S22C are wrought low-carbon non-alloy steels (C = 0.20–0.25%, Mn = 0.30–0.60%) that are used in the as rolled, normalized, or cold worked condition. These steels are widely used for lightly and moderately stressed parts that require higher strength levels than can be achieved by the lower carbon grades, and also for applications where a combination of low-to-medium strength, good cold formability, and good weldability are required. They may also be used in the carburized or carbonitrided, and subsequently quench hardened and tempered, condition for parts requiring a hard, wear-resistant surface, but with little need for increased mechanical properties in the core. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: CS-235. Producer or source: Data Survey.

SAE 1023 is a carbon steel of relatively low manganese content (0.30-0.60%); therefore, its hardenability, hardness and strength are somewhat lower than that of steels of higher manganese content at comparable carbon levels. It has good machinability, good workability (hot or cold) and good weldability. It is used in the annealed, hot worked, normalized or water-quenched-and-tempered condition for many automotive and general industry applications. It may be used in the carburized condition or without carburizing. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: CS-78. Producer or source: Carbon steel mills.

UGINOX MA4 (X46Cr13, No. 1.4034) is an age-hardenable martensitic stainless steel, mostly used where a sharp edge for cutting is needed. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and joining. Filing Code: SS-1023. Producer or source: Arcelor Stainless Processing LLC.

SP 700 is a high strength, beta-rich alpha-beta titanium alloy. It was developed with the following attributes: (1) excellent hot- and cold-workability; (2) enhanced hardenability with a wide range of mechanical properties that can be obtained by heat treatment; and (3) superior superplastic behavior at low temperature (around 1050 K). This datasheet provides information on composition, physical properties, microstructure, elasticity, tensile properties, and bend strength. It also includes information on high temperature performance as well as heat treating. Filing Code: TI-107. Producer or source: NKK Corporation.

Timetal 7-4 is an alpha + beta alloy with excellent creep resistance and high strength. This datasheet provides information on composition, physical properties, and tensile properties as well as creep. It also includes information on forming. Filing Code: Ti-151. Producer or source: Timet.

Timetal 551 is an improved-strength version of Timetal 550 alloy that retains good forging characteristics. The alpha-beta alloy has a nominal composition of Ti-4Al-4Mo-4Sn-0.5 Si, and it is used in gas turbine engine parts. This datasheet provides information on composition, physical properties, elasticity, tensile properties, and shear strength as well as creep. It also includes information on high temperature performance as well as forming and heat treating. Filing Code: TI-138. Producer or source: Timet.

TLP M4 is a powder metallurgy produced high-speed tool steel with a combination of wear resistance, high impact toughness, and transverse bend strength. This datasheet provides information on composition, physical properties, and hardness as well as fracture toughness. It also includes information on high temperature performance and wear resistance as well as heat treating. Filing Code: TS-586. Producer or source: Timken Latrobe Steel.

ARMCO NITRONIC 60 Stainless Steel provides outstanding galling and wear resistance. It also has excellent high-temperature oxidation resistance and low-temperature impact resistance. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on low and high temperature performance, and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SS-308. Producer or source: Baltimore Specialty Steels Corporation. Originally published as Nitronic 60, March 1975, revised July 1990.

Zapp TiAl6V4 is an alpha-beta titanium alloy that is used in the annealed or solution heat treated and aged condition for applications requiring high strength, relatively low weight, and excellent corrosion resistance. It is typically used in the low to moderate temperature range (up to about 400 °C, or 750 °F). Ti-6Al-4V is the most widely used titanium alloy, accounting for more than 50% of the total titanium used. The aerospace industry accounts for more than 80% of this usage. This datasheet provides information on composition, physical properties, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Ti-173. Producer or source: Zapp AG.

AL 468 is an 18% chromium stainless steel with dual stabilization by titanium and columbium. Small angular carbonitrides of both titanium and columbium are randomly dispersed, but develop improved surface quality, strength, and oxidation resistance when compared to Type 439. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as creep. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, and joining. Filing Code: SS-597. Producer or source: Allegheny Ludlum Corporation.

Micro-Melt 420-CW is a powder-produced wear-resistant tool steel with corrosion resistance. This datasheet provides information on composition, physical properties, hardness, and elasticity as well as fracture toughness. It also includes information on corrosion and wear resistance as well as forming, heat treating, machining, and powder metal forms. Filing Code: TS-676. Producer or source: Carpenter Powder Products.