1-20 of 360 Search Results for

1020

Sort by
Journal Articles
Alloy Digest (1987) 36 (2): CS-113.
Published: 01 February 1987
... SAE 1020 is a low-carbon steel combining good machinability, workability and weldability. It is carburized for use in case-hardened components and it is used for a wide range of applications in the hot-worked, cold-worked, normalized or quenched-and-tempered conditions. Its many uses include bolts...
Journal Articles
Alloy Digest (2022) 71 (5): CS-222.
Published: 01 May 2022
... 1020, C22, C22E, and C22R are wrought low-carbon non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. These steels are widely used for lightly and moderately stressed parts that require higher strength levels than can be achieved by the lower carbon...
Journal Articles
Alloy Digest (2023) 72 (10): CS-262.
Published: 01 October 2023
... 1020, C20E2C, and C22 are wrought low-carbon (carbon = 0.17–0.24%) non-alloy steels that are used in the as rolled, normalized, cold worked condition, or quenched and tempered condition. They are widely used for lightly and moderately stressed parts that require higher strength levels than can...
Journal Articles
Alloy Digest (1971) 20 (2): CS-39.
Published: 01 February 1971
... AISI 1020 is a low carbon steel combining good machinability, workability, and weldability. It is used for case-hardened components and for a wide range of applications in the hot-worked, cold-worked, normalized or quenched-and-tempered conditions. This datasheet provides information...
Journal Articles
Alloy Digest (2021) 70 (12): Ti-185.
Published: 01 December 2021
... Smiths Ti-6Al-2Sn-4Zr-2Mo-Si is a near-alpha titanium alloy that was developed for use at elevated temperatures. It exhibits high strength and toughness, excellent creep resistance, and high temperature stability at temperatures up 550 °C (1020 °F). This datasheet provides information...
Journal Articles
Alloy Digest (2006) 55 (4): Ni-634.
Published: 01 April 2006
... Nicrofer 4320 Ti is an age-hardening Ni-Fe-Cr alloy with both good corrosion resistance and high strength to 550 deg C (1020 deg F). It is a modification of alloy 825 and is often used in down-hole applications of sour wells. This datasheet provides information on composition, physical properties...
Journal Articles
Alloy Digest (2008) 57 (10): SS-1020.
Published: 01 October 2008
..., and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and machining. Filing Code: SS-1020. Producer or source: Valbruna Stainless Inc. Producer or Source: Valbruna Stainless Inc. Copyright © ASM International® 2008 2008 ASM International...
Journal Articles
Alloy Digest (1957) 6 (1): SS-51.
Published: 01 January 1957
... FIRTH-VICKERS 448 is a ferritic type stainless steel having high oxidation resistance and strength at elevated temperatures. It has good creep resistance in the range 1020 to 1200 deg. F. This datasheet provides information on composition, physical properties, elasticity, and tensile properties...
Journal Articles
Alloy Digest (2021) 70 (4): Ni-769.
Published: 01 April 2021
... VDM 601 (Nicrofer 6023 H) is a nickel-chromium-iron alloy with additions of aluminum and titanium. This alloy is specifically recommended for service above 550 °C (1020 °F) because of its superior creep-rupture properties resulting from its controlled carbon content and coarse grain size...
Journal Articles
Alloy Digest (1971) 20 (3): CS-19.
Published: 01 March 1971
... of Cut 0.010 in. 0.050 In. 0.100 in. Tool Speed Feed Speed Feed Speed Feed Steel Material fpm ipr fpm ipr fpm ipr Fremax 15 High Speed Steel 160 0.005 150 0.007 145 0.010 AISI 1020 High Speed Steel 120 0.005 115 0.007 110 0.010 Fremax 15 Brazed Carbide 600 0.006 570 0.010 540 0.015 Al.9 1020 Brazed...
Journal Articles
Alloy Digest (2022) 71 (7): TS-829.
Published: 01 July 2022
.... Stress Relieving. Heat to 650 °C (1200 °F). Wait for equalization of the temperature. Soak in a neutral atmosphere for 1 2 h. Cool slowly in the furnace. Quench Hardening. Heat to 1000 1020 °C (1830 1870 °F) for quenching in oil or in molten salt maintained at 500 550 °C (930 1020 °F), or to 1020 1040 °C...
Journal Articles
Alloy Digest (2020) 69 (1): TS-785.
Published: 01 January 2020
...) GPa 106 psi 180 26.1 Effect of Hardening and Tempering Temperatures on Hardness Hardness (HRC) at a tempering temperature of Hardening temperature 540 °C (1005 °F) 550 °C (1020 °F) 560 °C (1040 °F) 1000 °C (1830 °F) 57 59 56 58 54 56 1020 °C (1870 °F) 58 60 57 59 55 57 1050 °C (1920 °F) 59 61 58 60 56...
Journal Articles
Alloy Digest (2007) 56 (8): TS-653.
Published: 01 August 2007
... through to 650 °C (1200 °F) with a holding time of 2 h. Cool slowly to 500 °C (930 °F), then freely in air. Hardening. Preheat in two stages. The preheating temperature is 600 850 °C (1100 1560 °F), normally done in two preheating steps. Austenitizing temperature is 1020 1050 °C (1870 1920 °F), normally...
Journal Articles
Alloy Digest (2008) 57 (2): TS-661.
Published: 01 February 2008
... is the range of 1020 1050 °C (1870 1920 °F), normally 1020 1030 °C (1870 1885 °F). A hardening temperature of 1025 °C (1875 °F), with a soaking time of 30 min, results in a hardness of 53 ± 2 HRC before tempering. A hardening temperature of 1050 °C (1920 °F), DOI: 10.31399/asm.ad.ts0661 with a soaking time...
Journal Articles
Alloy Digest (2004) 53 (9): SS-909.
Published: 01 September 2004
...) Modulus of elasticity, GPa (106 psi) 20 °C (68 °F) 210 (30.5) 200 °C (390 °F) 200 (29) 400 °C (750 °F) 180 (26.1) (a) Test samples hardened in air from 1020 °C (1870 °F) and tempered twice to the given hard- ness. Specimens taken from a bar with dimensions 203 × 407 mm (8 × 16 in Impact Toughness. Stavax...
Journal Articles
Alloy Digest (2021) 70 (5): CS-210.
Published: 01 May 2021
.... 20 400 °C 14.28 (68 752 °F) (7.9) Tempering after Quench Hardening. Temper immediately after quench hardening. Heat to 550 660 °C (1020 1220 °F). 20 500 °C 14.79 (68 932 °F) (8.2) Wait for equalization of the temperature. Soak for at least 1 100 °C 51.1 h. Cool in still air. (212 °F) (29.5) Thermal W...
Journal Articles
Alloy Digest (2000) 49 (10): TS-581.
Published: 01 October 2000
...) and continue cooling in air. Hardening should be done under protective atmosphere. For the initial preheat, heat through to 650 C (1200 F). For the second preheat, heat through to 840 C (1550 F). The hardening tem- perature is 1020 1050 C (1870 1920 F). Hardening at 1020 C (1870 F) with a soak time...
Journal Articles
Alloy Digest (1980) 29 (1): CI-49.
Published: 01 January 1980
... PAB and PAC) Abrasion Testing Factor * Izod Impactt (Smooth, No Notch) Brinell MOY DSEF WSAF ft-lb Hardness?? -- SAE 1020 Steel (Annealed) 1 .oo 1 .oo - 100 Paraboloy PAB 0.060 0.36 16 550-700 Paraboloy PAC 0.058 0.47 22 500-700 *With both abrasion tests, lower factors indicate better wear resistance...
Journal Articles
Alloy Digest (2013) 62 (10): TS-722.
Published: 01 October 2013
...). Hardening. 1020 ºC (1868 ºF). Oil, hot quenching (500 550 ºC, 932 1022 ºF), air or vacuum with gas quenching. Holding time after temperature equalization: 15 to 30 minutes. Obtainable hardness: 52 54 HRC in oil or delayed martensitic hardening, 50 53 HRC in air or vacuum hardening. In order to prevent...
Journal Articles
Alloy Digest (2021) 70 (12): TS-822.
Published: 01 December 2021
...). Wait for equalization of the temperature. (c) Austenitizing: 1000 1050 °C (1830 1920 °F), but usually 1020 1030 °C (1870 1885 °F). Wait for equalization of temperature. Soak for 30 minutes. (e) Table 1 Hardness in the soft-annealed condition at room temperature Treatment condition Soft-annealed...